C1241 Low Power Supply Voltage Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2012
Versions by build date: Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012
DESCRIPTION
If there is a problem with the master cylinder solenoid (skid control ECU) power supply circuit, the skid control ECU outputs the DTC and prohibits operation under the fail-safe function.If the voltage supplied to terminal IG1 is not within the DTC detection threshold due to malfunctions in parts such as the battery and generator circuit, this DTC is stored.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1241 |
When either of following conditions detected: 1. Both of following conditions continue for at least 10 seconds.
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the master cylinder solenoid, perform zero point calibration (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When replacing the master cylinder solenoid, perform zero point calibration (Click here).
| 1. READ VALUE USING INTELLIGENT TESTER (IG VOLTAGE) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Start the engine.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item : Range
Normal Condition
Diagnostic Note
IG1 Voltage Value
IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V
11 to 14 V
Changes in proportion to battery voltage
Measure the voltage output from the ECU displayed on the tester.
Result Result
Proceed
Data display is within Normal Condition
A
Data display is not within Normal Condition
B
|
|
||||
| A | |
| 2. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Check if the same DTCs are output (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
Result Result
Proceed to
DTC is output
A
DTC is not output (When troubleshooting in accordance with Diagnostic Trouble Code Chart)
B
DTC is not output (When troubleshooting in accordance with Problem Symptoms Table)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 3. INSPECT SKID CONTROL ECU (IG1 TERMINAL) |
Disconnect the skid control ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A4-46 (IG1) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU)
|
|
||||
| OK | |
| 4. INSPECT SKID CONTROL ECU (GND TERMINAL) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
A4-1 (GND1) - Body ground
Always
Below 1 Ω
A4-32 (GND2) - Body ground
Always
Below 1 Ω
A5-4 (GND3) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU)
|
|
||||
| OK | |
| 5. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Check if the same DTCs are output (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
Result Result
Proceed to
DTC is output
A
DTC is not output (When troubleshooting in accordance with Diagnostic Trouble Code Chart)
B
DTC is not output (When troubleshooting in accordance with Problem Symptoms Table)
C
|
|
||||
|
|
||||
| A | ||
| ||
