DATA LIST / ACTIVE TEST
System information · Vehicles built Aug 2011 – Jul 2012
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014
| DATA LIST |
- HINT:
- According to the Data List displayed on the intelligent tester, you can read the values of components, such as the switches, sensors and actuators, without removing any parts. Reading the Data List as a first step of troubleshooting is one method of shortening labor time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are for reference only. Do not depend solely on these reference values when judging whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
According to the display on the tester, read the Data List.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Neutral Position SW Signal
PNP Switch Status/
OFF or ON
- OFF: Shift lever not in P and N
- ON: Shift lever in P or N
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, (Click here).
Transfer Neutral
Transfer status/
OFF or ON
- OFF: Transfer position not neutral
- ON: Transfer position in neutral
-
Transfer L4
Transfer status/
OFF or ON
- OFF: Transfer position not in L4
- ON: Transfer position in L4
-
Stop Light Switch
Stop Light Switch Status/
OFF or ON
- OFF: Brake Pedal is released
- ON: Brake Pedal is depressed
-
SPD (NT)
Input Turbine Speed/
Min.: 0 rpm
Max.: 12750 rpm
- Input turbine speed (NT) equal to the engine speed: Lock-Up ON (After warming up the engine)
- Input turbine speed (NT) nearly equal to the engine speed: Lock-Up OFF (Idling in N position)
Data is displayed in increments of 50 rpm
SPD (SP2)
Output shaft speed/
min.: 0 km/h (0 mph)
max.: 255 km/h (158 mph)
0 km/h (0 mph): Vehicle stopped
-
Shift SW Status (R Range)
PNP Switch Status/
OFF or ON
- OFF: Shift lever not in R
- ON: Shift lever in R
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, (Click here).
Shift SW Status (P Range)
PNP Switch Status/
OFF or ON
- OFF: Shift lever not in P
- ON: Shift lever in P
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, (Click here)
Shift SW Status (2 Range)
PNP Switch Status/
OFF or ON
- OFF: Shift lever not in 2 and L
- ON: Shift lever in 2 or L
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, (Click here).
Shift SW Status (L Range)
PNP Switch Status/
OFF or ON
- OFF: Shift lever not in L
- ON: Shift lever in L
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, (Click here).
Shift SW Status (N Range)
PNP Switch Status/
OFF or ON
- OFF: Shift lever not in N
- ON: Shift lever in N
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, (Click here)
Shift SW Status (D Range)
PNP Switch Status/
OFF or ON
- OFF: Shift lever not in D and 4
- ON: Shift lever in D or 4
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, (Click here).
Shift SW Status (4 Range)
PNP Switch Status/
OFF or ON
- OFF: Shift lever not in 4
- ON: Shift lever in 4
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, (Click here).
Shift SW Status (3 Range)
PNP Switch Status/
OFF or ON
- OFF: Shift lever not in 3
- ON: Shift lever in 3
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, (Click here).
A/T Oil Temperature 1
No. 1 ATF Temperature Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
- Approximately 80°C (176°F): After Stall Test
- Equal to ambient temperature during cold soak
If the value is "-40°C (-40°F)" or "150°C (302°F) or more", No. 1 ATF temperature sensor circuit is open or short.
A/T Oil Temperature 2
No. 2 ATF Temperature Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
- Approximately 80°C (176°F): After Stall Test
- Equal to ambient temperature during cold soak
If the value is "-40°C (-40°F)" or "150°C (302°F) or more", No. 2 ATF temperature sensor circuit is open or short.
Lock Up
Lock-up status/
OFF or ON
- OFF: Lock-up off
- ON: lock-up on
-
Shift Status
ECM gear shift command/
1st, 2nd, 3rd, 4th or 5th
Actual gear position
-
SLT Solenoid Status
Shift Solenoid SLT Status/
OFF or ON
- OFF: Accelerator pedal is depressed
- ON: Accelerator pedal is released
-
SLU Solenoid Status
Shift Solenoid SLU Status/
OFF or ON
- OFF: Lock-up off
- ON: lock-up on
-
AT Fluid
Lockup judder judgment/
OFF or ON
- OFF: Judder judgment does not occur
- ON: Judder judgment does not occur
-
- OFF: Shift lever not in P and N
| ACTIVE TEST |
- HINT:
- Performing the Active Test using the intelligent tester allows components, such as the relay, VSV, and actuator, to be operated without removing any parts. Performing the Active Test as a first step of troubleshooting is one method of shortening labor time.
- It is possible to display the Data List during the Active Test.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the tester, perform the Active Test.
Tester Display
Test Part
Control Range
Diagnostic Note
Active the Solenoid (SLU)
Operate the shift solenoid SLU
OFF or ON
[Vehicle Condition] - Engine stopped
- Shift lever on P or N position
Active the Solenoid (SLT)*
Operate the shift solenoid SLT and raise line pressure
OFF or ON - HINT:
- OFF: Line pressure up (when Active Test "Active the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
- ON: No action (normal operation)
- OFF: Line pressure up (when Active Test "Active the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
[Vehicle Condition] - Vehicle stopped
- Engine idling
Active the Solenoid (S1)
Operate the shift solenoid S1
OFF or ON
[Vehicle Condition] - Engine stopped
- Shift lever on P or N position
Active the Solenoid (S2)
Operate the shift solenoid S2
OFF or ON
[Vehicle Condition] - Engine stopped
- Shift lever on P or N position
Active the Lock Up
Control shift solenoid SLU to set automatic transmission to lock-up condition
OFF or ON
Possible to check shift solenoid valve SLU operation
[Vehicle Condition]- Throttle valve opening angle: Less than 35%
- Vehicle speed: 60 km/h (36 mph) or more
Control the Shift Position
Operate shift solenoid valve and set each shift position by yourself
- Press "→" button: Shift up
- Press "←" button: Shift down
Possible to check operation of shift solenoid valves
[Vehicle Condition]
50 km/h (30 mph) or less
Active the Solenoid (SR)
Operate the shift solenoid SR
OFF or ON
[Vehicle Condition] - Engine stopped
- Shift lever on P or N position
Active the Solenoid (SL1)
Operate the shift solenoid SL1
OFF or ON
[Vehicle Condition] - Engine stopped
- Shift lever on P or N position
Active the Solenoid (SL2)
Operate the shift solenoid SL2
OFF or ON
[Vehicle Condition] - Engine stopped
- Shift lever on P or N position
- Engine stopped
- HINT:
- The pressure values in Active Test and Hydraulic test are different from each other.