2011-2016 FJ Cruiser · Service Manual TRANSMISSION

DATA LIST / ACTIVE TEST

System information · Vehicles built Aug 2009 – Jul 2011

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014


DATA LIST

HINT:
According to the Data List displayed on a intelligent tester, you can read the values of components, such as the switches, sensors and actuators, without removing any parts. Reading the Data List as a first step of troubleshooting is one method of shortening labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are for reference only. Do not depend solely on these reference values when judging whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

  7. According to the display on the tester, read the Data List.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP Switch Status/
    ON or OFF
    Shift lever position is:
    P or N: ON
    Except P and N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, (Click here).

    Transfer Neutral
    Transfer status/
    ON or OFF
    1. Transfer position in neutral: ON
    2. Transfer position not neutral: OFF
    -
    Transfer L4
    Transfer status/
    ON or OFF
    1. Transfer position in L4: ON
    2. Transfer position not L4: OFF
    -
    Stop Light Switch
    Stop Light Switch Status/
    ON or OFF
    1. Brake Pedal is depressed: ON
    2. Brake Pedal is released: OFF
    -
    SPD (NT)
    Input Turbine Speed/
    Min.: 0 rpm
    Max.: 12750 rpm

    HINT:
    1. Lock-Up ON (After warming up the engine):
      Input turbine speed (NT) equal to the engine speed.
    2. Lock-Up OFF (Idling in N position):
      Input turbine speed (NT) nearly equal to the engine speed.

    Data is displayed in increments of 50 rpm
    SPD (SP2)
    Output shaft speed/
    min.: 0 km/h (0 mph)
    max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph)
    -
    Shift SW Status (R Range)
    PNP Switch Status/
    ON or OFF
    Shift lever position is:
    R: ON
    Except R: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, (Click here).

    Shift SW Status (2 Range)
    PNP Switch Status/
    ON or OFF
    Shift lever position is:
    2 or L: ON
    Except 2 and L: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, (Click here).

    Shift SW Status (L Range)
    PNP Switch Status/
    ON or OFF
    Shift lever position is:
    L: ON
    Except L: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, (Click here).

    Shift SW Status (D Range)
    PNP Switch Status/
    ON or OFF
    Shift lever position is:
    D or 4: ON
    Except D and 4: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, (Click here).

    Shift SW Status (4 Range)
    PNP Switch Status/
    ON or OFF
    Shift lever position is:
    4: ON
    Except 4: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, (Click here).

    Shift SW Status (3 Range)
    PNP Switch Status/
    ON or OFF
    Shift lever position is:
    3: ON
    Except 3: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, (Click here).

    A/T Oil Temperature 1
    No. 1 ATF Temperature Sensor Value/
    min.: -40°C (-40°F)
    max.: 215°C (419°F)
    1. After Stall Test:
      Approximately 80°C (176°F)
    2. Equal to ambient temperature during cold soak
    If the value is "-40°C (-40°F)" or "150°C (302°F) or more", No. 1 ATF temperature sensor circuit is open or short.
    A/T Oil Temperature 2
    No. 2 ATF Temperature Sensor Value/
    min.: -40°C (-40°F)
    max.: 215°C (419°F)
    1. After Stall Test:
      Approximately 80°C (176°F)
    2. Equal to ambient temperature during cold soak
    If the value is "-40°C (-40°F)" or "150°C (302°F) or more", No. 2 ATF temperature sensor circuit is open or short.
    Lock Up
    Lock-up status/
    ON or OFF
    1. Lock-up: ON
    2. Expect lock-up: OFF
    -
    Shift Status
    ECM gear shift command/
    1st, 2nd, 3rd, 4th or 5th
    Shift lever position is:
    1. L: 1st
    2. 2: 1st or 2nd
    3. 3: 1st, 2nd or 3rd
    4. 4: 1st, 2nd, 3rd or 4th
    5. D: 1st, 2nd, 3rd, 4th or 5th
    -
    SLT Solenoid Status
    Shift Solenoid SLT Status/
    ON or OFF
    1. Accelerator pedal is depressed: OFF
    2. Accelerator pedal is released: ON
    -
    SLU Solenoid Status
    Shift Solenoid SLU Status/
    ON or OFF
    1. Lock Up: ON
    2. Except Lock Up: OFF
    -
    AT Fluid
    Lockup judder judgment/
    ON or OFF
    1. Judder judgment occurs: ON
    2. Judder judgment does not occur: OFF
    -


ACTIVE TEST

HINT:
Performing the Active Test using a intelligent tester allows components, such as the relay, VSV, and actuator, to be operated without removing any parts. Performing the Active Test as a first step of troubleshooting is one method of shortening labor time.
It is possible to display the Data List during the Active Test.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the tester, perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Active the Solenoid (SLU)
    Operate the shift solenoid SLU
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N position
    Active the Solenoid (SLT)*
    Operate the shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Active the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    Active the Solenoid (S1)
    Operate the shift solenoid S1
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N position
    Active the Solenoid (S2)
    Operate the shift solenoid S2
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N position
    Active the Lock Up
    Control shift solenoid SLU to set automatic transmission to lock-up condition
    ON or OFF
    Possible to check shift solenoid valve SLU operation
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35%
    2. Vehicle speed: 60 km/h (36 mph) or more
    Control the Shift Position
    Operate shift solenoid valve and set each shift position by yourself
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of shift solenoid valves
    [Vehicle Condition]
    50 km/h (30 mph) or less
    Active the Solenoid (SR)
    Operate the shift solenoid SR
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N position
    Active the Solenoid (SL1)
    Operate the shift solenoid SL1
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N position
    Active the Solenoid (SL2)
    Operate the shift solenoid SL2
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever on P or N position

*: Active the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the HYDRAULIC TEST (Click here) as well. Please note that the pressure values in the Active Test and HYDRAULIC TEST are different.

HINT:
The pressure values in Active Test and HYDRAULIC TEST are different from each other.

← DATA LIST / ACTIVE TEST (Jul 2007 – Jul 2009)DATA LIST / ACTIVE TEST (Aug 2011 – Jul 2012) →