DATA LIST / ACTIVE TEST
System information · Vehicles built Jul 2007 – Jul 2009
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014
| DATA LIST |
- HINT:
- According to the Data List displayed on a intelligent tester, you can read the values of components, such as the switches, sensors and actuators, without removing any parts. Reading the Data List as a first step of troubleshooting is one method of shortening labor time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are for reference only. Do not depend solely on these reference values when judging whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch to OFF.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the tester, read the Data List.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
SPD (SP2)
Output shaft speed/
min.: 0 km/h (0 mph)
max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph)
-
SPD (NT)
Input Turbine Speed/
Min.: 0 rpm
Max.: 12750 rpm
[HINT] - Lock-Up ON (After warming up the engine):
Input turbine speed (NT) equal to the engine speed.
- Lock-Up OFF (Idling in N position):
Input turbine speed (NT) nearly equal to the engine speed.
Data is displayed in increments of 50 rpm
Neutral Position SW Signal
PNP Switch Status/
ON or OFF
Shift lever position is:
P or N: ON
Except P and N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
HINT:
When the failure still occurs even after adjusting these parts, Click here.
Stop Light Switch
Stop Light Switch Status/
ON or OFF
- Brake Pedal is depressed: ON
- Brake Pedal is released: OFF
-
Shift Status
ECM gear shift command/
1st, 2nd, 3rd, 4th or 5th
Shift lever position is: - L: 1st
- 2: 1st or 2nd
- 3: 1st, 2nd or 3rd
- 4: 1st, 2nd, 3rd or 4th
- D: 1st, 2nd, 3rd, 4th or 5th
-
Shift SW Status (R Range)
PNP Switch Status/
ON or OFF
Shift lever position is:
R: ON
Except R: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
HINT:
When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (D Range)
PNP Switch Status/
ON or OFF
Shift lever position is:
D or 4: ON
Except D and 4: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
HINT:
When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (4 Range)
PNP Switch Status/
ON or OFF
Shift lever position is:
4: ON
Except 4: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
HINT:
When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (3 Range)
PNP Switch Status/
ON or OFF
Shift lever position is:
3: ON
Except 3: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
HINT:
When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (2 Range)
PNP Switch Status/
ON or OFF
Shift lever position is:
2 or L: ON
Except 2 and L: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
HINT:
When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (L Range)
PNP Switch Status/
ON or OFF
Shift lever position is:
L: ON
Except L: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
HINT:
When the failure still occurs even after adjusting these parts, Click here.
A/T Oil Temperature 1
No. 1 ATF Temperature Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
- After Stall Test:
Approximately 80°C (176°F)
- Equal to ambient temperature during cold soak
If the value is "-40°C (-40°F)" or "150°C (302°F) or more", No. 1 ATF temperature sensor circuit is open or short.
A/T Oil Temperature 2
No. 2 ATF Temperature Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
- After Stall Test:
Approximately 80°C (176°F)
- Equal to ambient temperature during cold soak
If the value is "-40°C (-40°F)" or "150°C (302°F) or more", No. 2 ATF temperature sensor circuit is open or short.
Lock Up
Lock-up status/
ON or OFF
- Lock-up: ON
- Expect lock-up: OFF
-
Lock Up Solenoid Status
Lock Up Solenoid Status/
ON or OFF
- Lock Up: ON
- Except Lock Up: OFF
-
SLU Solenoid Status
Shift Solenoid SLU Status/
ON or OFF
- Lock Up: ON
- Except Lock Up: OFF
-
SLT Solenoid Status
Shift Solenoid SLT Status/
ON or OFF
- Accelerator pedal is depressed: OFF
- Accelerator pedal is released: ON
-
- Lock-Up ON (After warming up the engine):
| ACTIVE TEST |
- HINT:
- Performing the Active Test using a intelligent tester allows components, such as the relay, VSV, and actuator, to be operated without removing any parts. Performing the Active Test as a first step of troubleshooting is one method of shortening labor time.
- It is possible to display the Data List during the Active Test.
Warm up the engine.
Turn the ignition switch to OFF.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the tester, perform the Active Test.
Tester Display
Test Part
Control Range
Diagnostic Note
Active the Solenoid (SLU)
Operate the shift solenoid SLU
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever on P or N position
Active the Solenoid (SLT)*
Operate the shift solenoid SLT and raise line pressure
ON or OFF - HINT:
- OFF: Line pressure up (when Active Test "Active the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
- ON: No action (normal operation)
- OFF: Line pressure up (when Active Test "Active the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
[Vehicle Condition] - Vehicle stopped
- Engine idling
Active the Solenoid (S1)
Operate the shift solenoid S1
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever on P or N position
Active the Solenoid (S2)
Operate the shift solenoid S2
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever on P or N position
Active the Lock Up
Control shift solenoid SLU to set automatic transmission to lock-up condition
ON or OFF
Possible to check shift solenoid valve SLU operation
[Vehicle Condition]- Throttle valve opening angle: Less than 35%
- Vehicle speed: 60 km/h (36 mph) or more
Control the Shift Position
Operate shift solenoid valve and set each shift position by yourself
- Press "→" button: Shift up
- Press "←" button: Shift down
Possible to check operation of shift solenoid valves
[Vehicle Condition]
50 km/h (30 mph) or less
Active the Solenoid (SR)
Operate the shift solenoid SR
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever on P or N position
Active the Solenoid (SL1)
Operate the shift solenoid SL1
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever on P or N position
Active the Solenoid (SL2)
Operate the shift solenoid SL2
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever on P or N position
- Engine stopped
- HINT:
- The pressure values in Active Test and HYDRAULIC TEST are different from each other.