2011-2016 FJ Cruiser · Service Manual TRANSMISSION

P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input

Diagnostic trouble codes · Vehicles built from Aug 2009

Also covers:

DESCRIPTION

Refer to DTC P0711 (Click here ).
DTC No.
DTC Detection Conditions
Trouble Areas
P0712
No. 1 ATF temperature sensor resistance is less than 79 Ω for 0.5 seconds or more. (1-trip detection logic)
  1. Short in No. 1 ATF temperature sensor circuit
  2. Transmission wire (No. 1 ATF temperature sensor)
  3. ECM
P0713
NNo. 1 ATF temperature sensor resistance is more than 156 kΩ for 0.5 seconds or more, and either of the following conditions is met (1-trip detection logic):
  1. Open in No. 1 ATF temperature sensor circuit
  2. Transmission wire (No. 1 ATF temperature sensor)
  3. ECM
Condition (A): 9 minutes and 10 seconds or more have elapsed after the engine start when engine coolant temperature or intake air temperature is -29.375°C (- 20.875°F) or less.
Condition (B): 10 seconds or more have elapsed after the engine start when engine coolant temperature and intake air temperature are more than -29.375°C (- 20.875°F).

MONITOR DESCRIPTION

These DTCs indicate an open or short in the Automatic Transmission Fluid (ATF) temperature sensor circuit.
The ATF temperature sensor converts ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature, and detects any open or short malfunctions in the ATF temperature circuit. If the resistance value of the ATF temperature is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a fault in the ATF sensor or its wiring. The ECM turns on the MIL and stores a DTC.
*1: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.
*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

HINT:
The ATF temperature can be checked on a intelligent tester display.


WIRING DIAGRAM

Refer to DTC P0711 (Click here).

INSPECTION PROCEDURE

HINT:
According to the Data List displayed on a intelligent tester, you can read the values of components, such as the switches, sensors and actuators, without removing any parts. Reading the Data List as a first step of troubleshooting is one method of shortening labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are for reference only. Do not depend solely on these reference values when judging whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the tester on.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
  7. According to the display on the tester, read the Data List.
Engine and ECT 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
A/T Oil Temperature 1
No. 1 ATF Temperature Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
  1. After Stall Test:
    Approximately 80°C (176°F)
  2. Equal to ambient temperature during cold soak
If the value is "-40°C (-40°F)" or "150°C (302°F) or more", No. 1 ATF temperature sensor circuit is open or short.

HINT:
When DTC P0712 is output and intelligent tester reading is 150°C (302°F) or more, there is a short circuit.
When DTC P0713 is output and intelligent tester reading is -40°C (-40°F), there is an open circuit.
Measure the resistance between terminal THO1 and the body ground.

Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
150°C (302°F) or more
Short circuit

HINT:
If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 seconds). When P0713 is set, P0711 cannot be detected.
It is not necessary to inspect the circuit when P0711 is set.


1. INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)

  1. C213109E01
    Disconnect the transmission wire connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (OT-) - 10 (OT+)
    Always
    79 Ω to 156 kΩ
    2 (OT-) - Body ground
    Always
    10 kΩ or higher
    10 (OT+) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected:
    (Transmission Wire)

HINT:
If the resistance is outside the specified range at either of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

ATF Temperature
Specified Condition
10°C (50°F)
5 to 8 kΩ
25°C (77°F)
2.5 to 4.5 kΩ
110°C (230°F)
0.22 to 0.28 kΩ


NG
REPAIR OR REPLACE TRANSMISSION WIRE (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. C213116E01
    Connect the transmission wire connector to the transmission.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B49-5 (THO1) - B48-8 (ETHW)
    Always
    79 Ω to 156 kΩ
    B49-5 (THO1) - Body ground
    Always
    10 kΩ or higher
    B48-8 (ETHW) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector:
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0711 Transmission Fluid Temperature Sensor "A" Performance (from Aug 2014)P0717 Input Speed Sensor Circuit No Signal (Jul 2007 – Jul 2009) →