2011-2016 FJ Cruiser · Service Manual TRANSMISSION

P0717 Input Speed Sensor Circuit No Signal

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009

DESCRIPTION

This sensor detects the rotation speed of the turbine which shows the input revolution of the transmission. By comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (SP2), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, providing smooth gear shifts.
C124511E01
DTC No.
DTC Detection Conditions
Trouble Areas
P0717
All conditions below are detected for 5 seconds or more. (1-trip detection logic)
  1. (a) Gear change is not being performed.
  2. (b) Gear position: 4th or 5th
  3. (c) T/M input shaft rpm: 300 rpm or less
  4. (d) T/M output shaft rpm: 1,000 rpm or more
  5. (e) Park/neutral position switch (NSW, R and L) is OFF
  6. (f) Shift solenoid valves, park/neutral position switch and vehicle speed sensor are in normal operation.
  1. Open or short in speed sensor (NT) circuit
  2. Speed sensor (NT)
  3. ECM
Reference (Using an oscilloscope):
G020663E07
Check the waveform between terminals NT+ and NT- of the ECM connector.

Standard:
Refer to the illustration.
Item
Condition
Terminal
NT+ - NT-
Tool setting
2 V/DIV, 2 ms/DIV
Vehicle condition
Engine idling speed (P or N position)


MONITOR DESCRIPTION

This DTC indicates that a pulse is not output from the speed sensor NT (Turbine (input) speed sensor) or is weak. The NT terminal of the ECM detects the revolution signal from the speed sensor (NT) (input RPM). The ECM outputs a gearshift signal comparing the input speed sensor (NT) with the output speed sensor (SP2). While the vehicle is operating in the 4th or 5th gear position in the shift position of D, if the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is more than 1,000 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.
*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is approximately 50 km/h (31 mph) or more.

WIRING DIAGRAM

C166893E02

INSPECTION PROCEDURE

HINT:
According to the Data List displayed on a intelligent tester, you can read the values of components, such as the switches, sensors and actuators, without removing any parts. Reading the Data List as a first step of troubleshooting is one method of shortening labor time.

  1. Warm up the engine.
  2. Turn the ignition switch to OFF.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the tester ON.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List.
  7. According to the display on the tester, read the Data List.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
SPD (NT)
Input Turbine Speed/
Min.: 0 rpm
Max.: 12750 rpm
[HINT]
  1. Lock-Up ON (After warming up the engine):
    Input turbine speed (NT) equal to the engine speed.
  2. Lock-Up OFF (Idling in N position):
    Input turbine speed (NT) nearly equal to the engine speed.
Data is displayed in increments of 50 rpm

HINT:
  1. SPD (NT) is always 0 while driving:
    Open or short in the sensor or circuit.
  2. SPD (NT) is always less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:
    Sensor trouble, improper installation, or intermittent connection trouble of the circuit.


1. INSPECT SPEED SENSOR (NT) INSTALLATION

  1. BR03795E09
    Check the speed sensor (NT) installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



NG
SECURELY INSTALL OR REPLACE SPEED SENSOR (NT)
OK


2. INSPECT SPEED SENSOR (NT)

  1. C110343E35
    Disconnect the speed sensor (NT) connector from the transmission.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    560 to 680 Ω at 20°C (68°F)



NG
REPLACE SPEED SENSOR (NT) (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (SPEED SENSOR (NT) - ECM)

  1. G035616E68
    Connect the speed sensor (NT) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    B2-35 (NT+) - B2-27 (NT-)
    560 to 680 Ω at 20°C (68°F)

  1. Measure the resistance.

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    B2-35 (NT+) - Body ground
    10 kΩ or higher
    B2-27 (NT-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input (+ P0713) (from Aug 2009)P0717 Input Speed Sensor Circuit No Signal (from Aug 2009) →