2011-2016 FJ Cruiser · Service Manual TRANSMISSION

P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009

DESCRIPTION

C110339E03
The current flow to the solenoid is controlled by the duty ratio* of the ECM output signal. The higher the duty ratio becomes, the higher the lock-up hydraulic pressure becomes during the lock-up operation.
*: The duty ratio is the ratio of the continuity to non-continuity in one cycle.
For example, if A is the period of continuity in one cycle, and B is the period of non-continuity, then Duty Ratio = A/(A+B) x 100(%).
DTC No.
DTC Detection Conditions
Trouble Areas
P2759
Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while driving (1-trip detection logic)
  1. Open or short in shift solenoid valve SLU circuit
  2. Shift solenoid valve SLU
  3. ECM

MONITOR DESCRIPTION

When an open or short is detected in the shift solenoid valve (SLU) circuit, the ECM determines that there is a malfunction. The ECM turns on the MIL and stores this DTC.

WIRING DIAGRAM

C170064E04

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (SLU)
C110342E85
  1. Disconnect the transmission wire connector from the transmission.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    13 (SLU+) - 5 (SLU-)
    5.0 to 5.6 Ω at 20°C (68°F)

  1. Measure the resistance.

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    13 (SLU+) - Body ground
    10 kΩ or higher
    5 (SLU-) - Body ground
    10 kΩ or higher



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. G035616E67
    Connect the transmission wire connector to the transmission.

  1. Disconnect the ECM connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    B2-15 (SLU+) - B2-14 (SLU-)
    5.0 to 5.6 Ω at 20°C (68°F)

  1. Measure the resistance.

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    B2-15 (SLU+) - Body ground
    10 kΩ or higher
    B2-14 (SLU-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

3. INSPECT SHIFT SOLENOID VALVE SLU

  1. G020767E41
    Remove the shift solenoid valve SLU.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    5.0 to 5.6 Ω at 20°C (68°F)

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes operating sounds.



NG
REPLACE SHIFT SOLENOID VALVE SLU (Click here)
OK

REPAIR OR REPLACE TRANSMISSION WIRE (Click here)


← P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) (from Aug 2009)P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) (from Aug 2009) →