C1252 Brake Booster Pump Motor on Time Abnormally Long
Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012
Versions by build date: Nov 2010 – Jul 2012 from Aug 2012
DESCRIPTION
The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1252 |
Motor operates for 3 minutes or more. |
|
- HINT:
- The pump motor continues operation for the first 3 minutes, and then starts and stops repeatedly.
WIRING DIAGRAM
Refer to DTC C1251 (Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the master cylinder solenoid, perform zero point calibration (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When replacing the master cylinder solenoid, perform zero point calibration (Click here).
- HINT:
- When DTC C1253, C1254, C1256 or C1452 is output together with DTC C1252, inspect and repair the trouble area indicated by DTC C1253, C1254, C1256 or C1452 first.
| 1. CHECK HYDRAULIC BRAKE BOOSTER PUMP MOTOR OPERATION |
Turn the ignition switch off.
Depress the brake pedal more than 40 times.
Turn the ignition switch to ON.
Check how the pump motor operates.
Result Result
Proceed to
Pump motor does not operate
A
Pump motor operates continuously (Does not stop)
B
Pump motor operates intermittently
C
Pump motor operates, then stops
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. CHECK CONNECTION OF PUMP MOTOR WIRE HARNESS |
Remove the hydraulic brake booster assembly (Click here).
Check the tightening torque of the 2 screws which secure the wire harness connecting the master cylinder solenoid and brake booster with accumulator pump assembly.
- OK:
- The harness is tightened to the specified torque.
- Torque:
- 2.9 N*m{ 30 kgf*cm , 26 in.*lbf }
|
|
||||
| OK | |
| 3. CHECK RESISTANCE OF PUMP MOTOR WIRE HARNESS |
Using a screwdriver, remove the 2 screws and pull out the wire harness from the master cylinder solenoid.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Red wire terminal - Black wire terminal
Always
Below 2 Ω
Text in Illustration *1
Pump motor wire harness
*a
Red wire
*b
Black wire
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (ACCUMULATOR SENSOR) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item / Range
Normal Condition
Diagnostic Note
Accumulator Sensor
Accumulator pressure sensor reading / min.: 0 V, max.: 5 V
3.58 to 5 V
If value constant regardless of pump operation, accumulator pressure sensor malfunction suspected.
Check that the accumulator pressure sensor output is normal.
Result Result
Proceed to
Output value varies within "Normal Condition" range
A
Output value does not reach "Normal Condition" range
B
Output value constant regardless of pump motor operation
C
|
|
||||
|
|
||||
| A | |
| 5. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON.
Wait for more than 5 minutes.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is output
A
DTC is not output
B
|
|
||||
| A | ||
| ||
