P0717 Input Speed Sensor Circuit No Signal
Diagnostic trouble codes · Vehicles built from Aug 2009
Versions by build date: Jul 2007 – Jul 2009 from Aug 2009
DESCRIPTION
This sensor detects the rotation speed of the turbine which shows the input revolution of the transmission. By comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (SP2), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, providing smooth gear shifts.| DTC No. |
DTC Detection Conditions |
Trouble Areas |
| P0717 |
All conditions below are detected for 5 seconds or more. (1-trip detection logic)
|
|


Check the waveform between terminals NT+ and NT- of the ECM connector.
- Standard:
- Refer to the illustration.
| Item |
Condition |
| Terminal |
NT+ - NT- |
| Tool setting |
2 V/DIV, 2 ms/DIV |
| Vehicle condition |
Engine idling speed (P or N position) |
MONITOR DESCRIPTION
This DTC indicates that a pulse is not output from the speed sensor NT (Turbine (input) speed sensor) or is weak. The NT terminal of the ECM detects the revolution signal from the speed sensor (NT) (input RPM). The ECM outputs a gearshift signal comparing the input speed sensor (NT) with the output speed sensor (SP2). While the vehicle is operating in the 4th or 5th gear position in the shift position of D, if the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is more than 1000 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is approximately 50 km/h (31 mph) or more.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- According to the Data List displayed on a intelligent tester, you can read the values of components, such as the switches, sensors and actuators, without removing any parts. Reading the Data List as a first step of troubleshooting is one method of shortening labor time.
- Warm up the engine.
- Turn the ignition switch off.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch to ON.
- Turn the tester on.
- Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
- According to the display on the tester, read the Data List.
| Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
| SPD (NT) |
Input Turbine Speed/ Min.: 0 rpm Max.: 12750 rpm |
|
Data is displayed in increments of 50 rpm |
- HINT:
- SPD (NT) is always 0 while driving:
Open or short in the sensor or circuit.
- SPD (NT) is always less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:
Sensor trouble, improper installation, or intermittent connection trouble of the circuit.
- SPD (NT) is always 0 while driving:
| 1. INSPECT SPEED SENSOR (NT) INSTALLATION |
Check the speed sensor (NT) installation.

- OK:
- The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.
Text in Illustration *a
Correct
*b
Incorrect
*c
Clearance
|
|
||||
| OK | |
| 2. INSPECT SPEED SENSOR (NT) |
Disconnect the speed sensor (NT) connector from the transmission.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
560 to 680 Ω
Text in Illustration *1
Component without harness connected:
(Speed Sensor (NT))
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (SPEED SENSOR (NT) - ECM) |
Connect the speed sensor (NT) connector.

Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B49-3 (NT+) - B49-4 (NT-)
20°C (68°F)
560 to 680 Ω
B49-3 (NT+) - Body ground
Always
10 kΩ or higher
B49-4 (NT-) - Body ground
Always
10 kΩ or higher
Text in Illustration *1
Rear view of wire harness connector:
(to ECM)
|
|
||||
| OK | ||
| ||
