DATA LIST / ACTIVE TEST
System information · Vehicles built Jul 2007 – Oct 2010
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012
| READ DATA LIST |
- HINT:
- Using a intelligent tester to read the Data List allows the values or states of switches, sensor, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may by discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the tester on.
Enter the following menus: Body Electrical / Body / Data List /
According to the display on tester, read the "Data List".
Body (Main Body ECU): Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D Door Courtesy SW
Driver door courtesy switch signal/ON or OFF
ON :Driver door is open
OFF: Driver door is closed
-
P Door Courtesy SW
Front passenger door courtesy switch signal/ON or OFF
ON: Front passenger door is open
OFF: Front passenger door is closed
-
RR Door Courtesy SW
Rear door courtesy switch RH (Lower and upper) signal/ON or OFF
ON: Rear door RH is open
OFF: Rear door RH are closed
-
RL Door Courtesy SW
Rear door courtesy switch (LH side lower and upper) signal/ON or OFF
ON: Rear door LH is open
OFF: Rear door LH are closed
-
Luggage Courtesy SW
Back door and back window courtesy switch signal/ON or OFF
ON: Either back door or back window is open
OFF: Both back door and back window are closed
-
Dimmer SW
Dimmer switch signal/ON or OFF
ON: Dimmer switch is ON (High Beam) or High flasher switch is ON
OFF: Dimmer switch is OFF (Low Beam) or High flasher switch is OFF
-
High Flasher SW
High flasher switch signal/ON or OFF
ON: High flasher switch is ON
OFF: High flasher switch is OFF
-
Head Light SW
Headlight switch signal/ON or OFF
ON: Light control switch is in HEAD position
OFF: Light control switch is not in HEAD position
-
Tail Light SW
Taillight switch signal/ON or OFF
ON: Light control switch is in TAIL or HEAD position
OFF: Light control switch is OFF
-
Alternator L Terminal
Generator L terminal signal/ON or OFF
ON: Engine start Charge warning light is OFF
OFF: Engine start Charge warning light is ON
-
| PERFORM ACTIVE TEST |
- HINT:
- Using a intelligent tester to Perform the Active Tests allows relays, VSVs and actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the tester on.
Enter the following menus: Body Electrical / Body / Active Test /
According to the display on tester, perform the "Active Test".
Body (Main Body ECU): Tester Display
Test Part
Control Range
Normal Condition
Illuminated Entry System
Transponder key amplifier (Ignition key cylinder light)
Room light and rear room light (Room lights switch is in DOOR position and all doors are closed)
ON/OFF
-
Hazard
Turn signal flasher
ON/OFF
-
Tail Light
Taillight Relay
ON/OFF
-
Head Light
Headlight Relay
ON/OFF
-
Doom Relay Cut
DOME relay
ON/OFF
-
Open Door Warning Light
Open door warning light
ON/OFF
-