DATA LIST / ACTIVE TEST
System information · Vehicles built from Aug 2012
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- CAUTION:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Body Electrical/ Body / Data List.
According to the display on the tester, read the Data List.
Body (Main Body) Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ACC SW
Ignition switch signal/ OFF or ON
OFF: Ignition switch off
ON: Ignition switch ACC or ON
-
IG SW
Ignition switch signal/ OFF or ON
OFF: Ignition switch ACC or off
ON: Ignition switch ON
-
Luggage Courtesy SW
Back door and back window courtesy switch signal/ OFF or ON
OFF: Both back door and back window are closed
ON: Either back door or back window is open
-
D Door Courtesy SW
Driver side door courtesy light switch signal/ OFF or ON
OFF: Driver side door is closed
ON: Driver side door is open
-
P Door Courtesy SW
Passenger side door courtesy light switch signal/ OFF or ON
OFF: Passenger side door is closed
ON: Passenger side door is open
-
Rear Door Courtesy SW
Rear door courtesy light switch signal/ OFF or ON
OFF: Rear door is closed
ON: Rear door is open
-
Passing Light SW
Dimmer switch HIGH FLASH signal/ OFF or ON
OFF: Dimmer switch not in HIGH FLASH (Pass)
ON: Dimmer switch in HIGH FLASH (Pass)
-
Head Light SW (Head)
Light control switch HEAD signal/ OFF or ON
OFF: Light control switch not in HEAD
ON: Light control switch in HEAD
-
Head Light SW (Tail)
Light control switch TAIL signal/ OFF or ON
OFF: Light control switch in neither TAIL nor HEAD
ON: Light control switch in TAIL or HEAD
-
Lighting Time
Lighting time after closing all doors / 15 s, 7.5 s or 30 s
Customized setting displayed
-
I/L when ACC OFF
Function which turns on lights when ignition switch is turned from ACC to off / OFF or ON
Customized setting displayed
-
I/L ON W/Unlock
Function which turns on interior lights when door is unlocked / OFF or ON
Customized setting displayed
-
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Body Electrical / Body / Active Test.
According to the display on the tester, perform the Active Test.
Body (Main Body) Tester Display
Test Part
Control Range
Normal Condition
Hazard
Turn signal flasher
OFF/ON
-
Headlight Relay
Headlight Relay
OFF/ON
-
Taillight Relay
Taillight Relay
OFF/ON
-
Illuminated Entry System
Transponder key amplifier (Ignition key cylinder light)
Room light and rear room light (Room lights switch is in DOOR position and all doors are closed)
OFF/ON
-
Doom Relay Cut
DOME Relay
OFF/ON
-