2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1655/37 Seat Belt Buckle Switch RH Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2012

DESCRIPTION

The seat belt buckle switch RH circuit consists of the center airbag sensor assembly and front seat inner belt assembly RH.
DTC B1655/37 is stored when a malfunction is detected in the seat belt buckle switch RH circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1655/37
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch RH circuit.
  2. Front seat inner belt assembly RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat inner belt assembly RH (Seat belt buckle switch RH)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C268583E01

INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).


1. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and front seat inner belt assembly RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and front seat inner belt assembly RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


2. CHECK FLOOR WIRE (OPEN)

  1. C268584E04
    Using a service wire, connect terminals 15 (RBE+) and 14 (RBE-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K15-1 (RBE+) - K15-3 (RBE-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly RH
    *2
    Center Airbag Sensor Assembly
    *3
    Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly RH)



NG
REPLACE FLOOR WIRE
OK


3. CHECK FLOOR WIRE (SHORT TO GROUND)

  1. C268585E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K15-1 (RBE+) - Body ground
    Always
    1 MΩ or higher
    K15-3 (RBE-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly RH
    *2
    Center Airbag Sensor Assembly
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly RH)



NG
REPLACE FLOOR WIRE
OK


4. CHECK FLOOR WIRE (SHORT)
C268585E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K15-1 (RBE+) - K15-3 (RBE-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly RH
    *2
    Center Airbag Sensor Assembly
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly RH)



NG
REPLACE FLOOR WIRE
OK


5. CHECK FLOOR WIRE (SHORT TO B+)

  1. C268585E03
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    K15-1 (RBE+) - Body ground
    Ignition switch ON
    Below 1 V
    K15-3 (RBE-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly RH
    *2
    Center Airbag Sensor Assembly
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly RH)



NG
REPLACE FLOOR WIRE
OK


6. CHECK DTC

  1. C268576E01
    Connect the connectors to the center airbag sensor assembly and front seat inner belt assembly RH.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    Codes other than DTC B1655/37 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly RH
    *2
    Center Airbag Sensor Assembly



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)

7. CHECK FRONT SEAT INNER BELT ASSEMBLY RH

  1. C268576E01
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Replace the front seat inner belt assembly RH with a known good one (Click here).

    HINT:
    Perform the following inspection using known good parts from another vehicle if possible.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    Codes other than DTC B1655/37 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Return the front seat inner belt assembly RH that was installed for testing to its original location (Click here).

    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly RH
    *2
    Center Airbag Sensor Assembly



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (Click here)


← B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction (Nov 2010 – Jul 2012)B1656/38 Seat Belt Buckle Switch LH Circuit Malfunction (from Aug 2012) →