2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012

DESCRIPTION

The driver side seat belt buckle switch circuit consists of the center airbag sensor assembly and the front seat inner belt assembly (driver side).
DTC B1655/37 is recorded when a malfunction is detected in the driver side seat belt buckle switch circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1655/37
  1. Center airbag sensor assembly detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in driver side seat belt buckle switch circuit for 2 seconds.
  2. Front seat inner belt assembly (driver side) malfunction
  3. Center airbag sensor assembly malfunction
  1. Driver side floor wire
  2. Front seat inner belt assembly (Driver Side)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C158843E12
C158843E14

INSPECTION PROCEDURE


1. CHECK DTC OUTPUT (CENTER AIRBAG SENSOR ASSEMBLY)
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    DTCs other than DTC B1655/37 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front seat inner belt assembly (driver side).

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3. CHECK DRIVER SIDE FLOOR WIRE

  1. H100893E04
    Check for open in the circuit.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front Seat Inner Belt Assembly (Driver Side)
    *b
    Center Airbag Sensor Assembly
    *c
    Driver Side Floor Wire
    *d
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly)
    *e
    Rear view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *f
    Connector C
    *g
    Connector B
    *h
    Service Wire
    1. Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt assembly (Driver side).

    2. Using a service wire, connect 11 and 12 of connector B.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      L17-1 (LBE+) - L17-3 (LBE-)
      Always
      Below 1 Ω
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      K15-1 (RBE+) - K15-3 (RBE-)
      Always
      Below 1 Ω

  1. H100159E04
    Check for short in the circuit.
    1. Disconnect the service wire from connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      L17-1 (LBE+) - L17-3 (LBE-)
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      K15-1 (RBE+) - K15-3 (RBE-)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      L17-1 (LBE+) - Body ground
      Always
      1 MΩ or higher
      L17-3 (LBE-) - Body ground
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      K15-1 (RBE+) - Body ground
      Always
      1 MΩ or higher
      K15-3 (RBE-) - Body ground
      Always
      1 MΩ or higher

  1. Check for short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      L17-1 (LBE+) - Body ground
      Ignition switch ON
      Below 1 V
      L17-3 (LBE-) - Body ground
      Ignition switch ON
      Below 1 V
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      K15-1 (RBE+) - Body ground
      Ignition switch ON
      Below 1 V
      K15-3 (RBE-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Front Seat Inner Belt Assembly (Driver Side)
      *b
      Center Airbag Sensor Assembly
      *c
      Driver Side Floor Wire
      *d
      Front view of wire harness connector
      (to Front Seat Inner Belt Assembly)
      *e
      Connector C



NG
REPLACE DRIVER SIDE FLOOR WIRE
OK


4. CHECK FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)
  1. Connect the connectors to the center airbag sensor assembly and the front seat inner belt assembly (driver side).

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    DTCs other than DTC B1655/37 may be output at this time, but they are not related to this check.



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)

5. REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat inner belt assembly (driver side) (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


6. CHECK CENTER AIRBAG SENSOR ASSEMBLY
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    DTCs other than DTC B1655/37 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END


← B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction (Jul 2007 – Oct 2010)B1655/37 Seat Belt Buckle Switch RH Circuit Malfunction (from Aug 2012) →