2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Headlight Beam Level Control Actuator Circuit

Circuit diagnosis · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

The headlight leveling motors are activated by operating the headlight leveling switch, allowing the headlight beam angle to be adjusted.

WIRING DIAGRAM

E219605E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


1. INSPECT HEADLIGHT LEVELING SWITCH
  1. Inspect the headlight leveling switch (Click here).



NG
REPLACE HEADLIGHT LEVELING SWITCH (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING SWITCH - HEAD RELAY AND BODY GROUND)

  1. E162339E02
    Disconnect the E74 headlight leveling switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E74-1 (+B) - Body ground
    Ignition switch ON
    Light control switch in HEAD position
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E74-2 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Headlight Leveling Switch)

  1. Reconnect the headlight leveling switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - HEAD RELAY AND BODY GROUND)

  1. E162340E02
    Disconnect the A34 and A37 headlight assembly connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A34-3 (RHB1) - Body ground
    Ignition switch ON
    Light control switch in HEAD position
    11 to 14 V
    A37-3 (LHB1) - Body ground
    Ignition switch ON
    Light control switch in HEAD position
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A34-1 (RHE) - Body ground
    Always
    Below 1 Ω
    A37-1 (LHE) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Headlight Leveling Motor)
    *b
    LH Side
    *c
    RH Side

  1. Reconnect the headlight assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING SWITCH - HEADLIGHT ASSEMBLY)
  1. Disconnect the E74 headlight leveling switch connector.

  1. Disconnect the A34 and A37 headlight assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E74-4 (LH0) - A37-2 (LHM)
    Always
    Below 1 Ω
    E74-5 (RH0) - A34-2 (RHM+)
    Always
    Below 1 Ω
    E74-4 (LH0) - Body ground
    Always
    10 kΩ or higher
    E74-5 (RH0) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the headlight assembly connectors.

  1. Reconnect the headlight leveling switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HEADLIGHT ASSEMBLY (HEADLIGHT LEVELING MOTOR) (Click here)


← Headlight Beam Level Control Actuator Circuit (Jul 2007 – Oct 2010)COMPONENTS (from Jul 2007) →