Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM
Rear Fog Light Circuit
Circuit diagnosis · Vehicles built Jul 2007 – Oct 2010
Versions by build date: Jul 2007 – Oct 2010 from Nov 2010
DESCRIPTION
The rear fog light illuminates only when the headlight dimmer switch is in the HEAD position. When the switch is turned to OFF, the rear fog light turns off automatically. WIRING DIAGRAM
INSPECTION PROCEDURE
1. CHECK VEHICLE CONDITION
Check whether the rear fog lights illuminate.
OK:
Rear fog lights illuminate.
Result
Result
Proceed to
Neither left nor right rear fog light illuminates
A
Either left or right rear fog light illuminates
B
B
A
2. INSPECT FUSE (RR FOG, TAIL)
Remove the RR FOG fuse from the engine room relay block.
Remove the TAIL fuse from the main body ECU.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
RR FOG fuse
Always
Below 1 Ω
TAIL fuse
Always
Below 1 Ω
Reinstall the RR FOG and TAIL fuse.
NG
OK
3. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT SWITCH - BATTERY, TAIL RELAY)
Disconnect the E75 rear fog light switch connector.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E75-3 (ILL+) - Body ground
Light control switch TAIL or HEAD
11 to 14 V
E75-4 (B) - Body ground
Always
11 to 14 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
4. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT SWITCH - MAIN BODY ECU)
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E75-6 (LH) - Body ground
Light control switch OFF or TAIL
11 to 14 V
Light control switch HEAD
Below 1 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
5. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT SWITCH - BODY GROUND)
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
E75-1 (E) - Body ground
Always
Below 1 Ω
Reconnect the rear fog light switch connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
6. INSPECT REAR FOG LIGHT SWITCH (OUTPUT VOLTAGE)
Remove the rear fog light switch with its connector still connected.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
8 (L) - Body ground
Light control switch HEAD Rear fog light switch FREE
Below 1 V
Light control switch HEAD Rear fog light switch full traveling
11 to 14 V
Reinstall the rear fog light switch.
NG
OK
7. INSPECT BULB (REAR FOG LIGHT BULB)
Remove the rear fog light.
Apply battery voltage to the terminals and check that the rear fog light illuminates.
OK:
Measurement Condition
Specified Condition
Positive battery (+) → 1 Negative battery (-) → 2
Rear fog light illuminates
Reinstall the rear fog light.
NG
OK
8. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT SWITCH - REAR FOG LIGHT)
Disconnect the N4 and N5 rear fog light connectors.
Measure the voltage.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
N4-1 - Body ground
Ignition switch ON Light control switch HEAD Rear fog light switch full traveling
11 to 14 V
N5-1 - Body ground
11 to 14 V
Reconnect the rear fog light connectors.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR FOG LIGHT - BODY GROUND)