2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Rear Fog Light Circuit

Circuit diagnosis · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

The rear fog light illuminates only when the headlight dimmer switch is in the HEAD position. When the switch is turned to OFF, the rear fog light turns off automatically.

WIRING DIAGRAM

E214774E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


1. CHECK VEHICLE CONDITION
  1. Check whether the rear fog lights illuminate.

    Result 
    Result
    Proceed to
    Neither left nor right rear fog light illuminates
    A
    Either left or right rear fog light illuminates
    B



B
Go to step 5
A


2. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT SWITCH - BATTERY, TAIL RELAY AND BODY GROUND)

  1. E162333E04
    Disconnect the E75 rear fog light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-3 (ILL+) - Body ground
    Light control switch TAIL or HEAD
    11 to 14 V
    E75-4 (B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-1 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Fog Light Switch)

  1. Reconnect the rear fog light switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT SWITCH - MAIN BODY ECU)
  1. Disconnect the E75 rear fog light switch connector.

  1. E162333E05
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-6 (LH) - Body ground
    Light control switch OFF or TAIL
    11 to 14 V
    Light control switch HEAD
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Fog Light Switch)

  1. Reconnect the rear fog light switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT REAR FOG LIGHT SWITCH (OUTPUT VOLTAGE)

  1. E162335E02
    Remove the rear fog light switch with its connector still connected.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-8 (L) - Body ground
    Light control switch HEAD
    Rear fog light switch FREE
    Below 1 V
    Light control switch HEAD
    Rear fog light switch full traveling
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Rear Fog Light Switch)

  1. Reinstall the rear fog light switch.



NG
REPLACE REAR FOG LIGHT SWITCH (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT ASSEMBLY - REAR FOG LIGHT SWITCH - BODY GROUND)
  1. Disconnect the N4 and N5 rear fog light assembly connectors.

  1. Disconnect the E75 rear fog light switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    N4-1 - E75-8 (L)
    Always
    Below 1 Ω
    N4-1 - Body ground
    Always
    10 kΩ or higher
    N4-2 - Body ground
    Always
    Below 1 Ω
    N5-1 - E75-8 (L)
    Always
    Below 1 Ω
    N5-1 - Body ground
    Always
    10 kΩ or higher
    N5-2 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the rear fog light switch connectors.

  1. Reconnect the rear fog light assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR FOG LIGHT ASSEMBLY (Click here)


← Rear Fog Light Circuit (Jul 2007 – Oct 2010)Turn Signal Light Circuit (Jul 2007 – Oct 2010) →