2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Turn Signal Light Circuit

Circuit diagnosis · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2014 from Aug 2014

DESCRIPTION

The turn signal flasher relay turns on when it receives signals from the headlight dimmer switch integrated with the turn signal switch, causing the turn signal lights to flash.

WIRING DIAGRAM

E162313E01

INSPECTION PROCEDURE


1. CHECK OPERATION (TURN SIGNAL LIGHT)
  1. When the turn signal light switch is operated, check that the appropriate turn signal light flashes.

    Result 
    Condition
    Proceed to
    No lights flash
    A
    Front turn signal light (LH or RH) does not flash
    B
    Rear turn signal light (LH or RH) does not flash
    C
    Side turn signal light (LH or RH) does not flash*
    D
    1. *: w/ Side turn signal light



B
Go to step 7

C
Go to step 9

D
Go to step 11
A


2. INSPECT FUSE (IG1, TRN-HAZ)
  1. Remove the IG1 fuse from the main body ECU.

  1. Remove the TRN-HAZ fuse from the No. 2 engine room relay block.

  1. Measure the resistance according value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IG1 fuse
    Always
    Below 1 Ω
    TRN-HAZ fuse
    Always
    10 kΩ or higher

  1. Reinstall the IG1 and TRN-HAZ fuses.



NG
REPLACE FUSE
OK


3. INSPECT TURN SIGNAL FLASHER RELAY
  1. Remove the turn signal flasher relay with its connector still connected.

  1. E162314E01
    Measure the voltage according value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (LR) - Body ground
    Turn signal switch (right turn) OFF → ON
    0 V → 11 to 14 V (60 to 120 times per minute)
    3 (LL) - Body ground
    Turn signal switch (left turn) OFF → ON
    0 V → 11 to 14 V (60 to 120 times per minute)
    5 (EL) - Body ground
    Turn signal switch (left turn) OFF → ON
    11 to 14 V → 0 V
    6 (ER) - Body ground
    Turn signal switch (right turn) OFF → ON
    11 to 14 V → 0 V

  1. Reinstall the turn signal flasher relay.



NG
REPLACE TURN SIGNAL FLASHER RELAY
OK


4. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER RELAY - FUSE, BODY GROUND)

  1. E120966E19
    Disconnect the E9 turn signal flasher relay connector.

  1. Measure the voltage according value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E9-1(IG) - Body ground
    Ignition switch ON
    11 to 14 V
    E9-4 (B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E9-7 (E) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the turn signal flasher relay connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT HEADLIGHT DIMMER SWITCH (TURN SIGNAL LIGHT SWITCH)

  1. E162315E01
    Remove the headlight dimmer switch.

  1. Inspect the turn signal light switch.

    1. Measure the resistance according value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      2 (TB) - 3 (TR)
      Right
      Below 1 Ω
      2 (TB) - 3 (TR)
      Neutral
      10 kΩ or higher
      2 (TB) - 1 (TL)
      Left
      Below 1 Ω
      2 (TB) - 1 (TL)
      Neutral
      10 kΩ or higher

  1. Reinstall the headlight dimmer switch.



NG
REPLACE HEADLIGHT DIMMER SWITCH (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER RELAY - HEADLIGHT DIMMER SWITCH)

  1. B136087E02
    Disconnect the E20 headlight dimmer switch connector.

  1. Disconnect the E9 turn signal flasher relay connector.

  1. Measure the resistance according value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E20-2 (TB) - E9 -7 (E)
    Always
    Below 1 Ω
    E20-2 (TB) or E9 -7 (E) - Body ground
    Always
    10 kΩ or higher
    E20-1 (TL) - E9-5 (EL)
    Always
    Below 1 Ω
    E20-1 (TL) or E9-5 (EL) - Body ground
    Always
    10 kΩ or higher
    E20-3 (TR) - E9-6 (ER)
    Always
    Below 1 Ω
    E20-3 (TR) or E9-6 (ER) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the headlight dimmer switch connector.

  1. Reconnect the turn signal flasher relay connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT DIMMER SWITCH - BODY GROUND)

7. INSPECT BULB (FRONT TURN SIGNAL LIGHT BULB)

  1. B136088E02
    Remove the front turn signal light.

  1. Apply battery voltage to the terminals and check that the front turn signal light illuminates.

    OK:
    Measurement Condition
    Specified Condition
    Positive battery - Terminal 3
    Negative battery - Terminal 2
    Front turn signal light illuminates

  1. Reinstall the front turn signal light.



NG
REPLACE BULB (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER RELAY - FRONT TURN SIGNAL LIGHT)

  1. B136089E02
    Disconnect the E9 turn signal flasher relay connector.

  1. Disconnect the A16 and A20 front turn signal light connectors.

  1. Measure the resistance according value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E9-2 (LR) - A20-3
    Always
    Below 1 Ω
    E9-2 (LR) or A20-3 - Body ground
    Always
    10 kΩ or higher
    E9-3 (LL) - A16-3
    Always
    Below 1 Ω
    E9-3 (LL) or A16-3 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the turn signal flasher relay connector.

  1. Reconnect the front turn signal light connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT TURN SIGNAL LIGHT - BODY GROUND)

9. INSPECT BULB (REAR TURN SIGNAL LIGHT BULB)
E162316E01
  1. w/o Rear fog light

    1. Remove the rear turn signal light.

    2. Apply battery voltage to the terminals and check that the rear turn signal light illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Positive battery - Terminal 1
      Negative battery - Terminal 2
      Rear turn signal light illuminates

    3. Reinstall the rear turn signal light.

  1. w/ Rear fog light

    1. Remove the rear turn signal light.

    2. Apply battery voltage to the terminals and check that the rear turn signal light illuminates.

      OK:
      Measurement Condition
      Specified Condition
      Positive battery - Terminal 1
      Negative battery - Terminal 2
      Rear turn signal light illuminates

    3. Reinstall the rear turn signal light.

Result 
Result
Proceed to
OK
A
NG (w/o Rear fog light)
B
NG (w/ Rear fog light)
C


B
REPLACE BULB (Click here)

C
REPLACE BULB (Click here)
A


10. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER RELAY - REAR TURN SIGNAL LIGHT)
E162317E01
  1. w/o Rear fog light

    1. Disconnect the E9 turn signal flasher relay connector.

    2. Disconnect the L12 and L15 rear turn signal light connectors.

    3. Measure the resistance according value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E9-2 (LR) - L15-1
      Always
      Below 1 Ω
      E9-2 (LR) or L15-1 - Body ground
      Always
      10 kΩ or higher
      E9-3 (LL) - L12-1
      Always
      Below 1 Ω
      E9-3 (LL) or L12-1 - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the turn signal flasher relay connector.

    5. Reconnect the rear turn signal light connectors.

  1. w/ Rear fog light

    1. Disconnect the E9 turn signal flasher relay connector.

    2. Disconnect the N2 and N3 rear turn signal light connectors.

    3. Measure the resistance according value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E9-2 (LR) - N2-1
      Always
      Below 1 Ω
      E9-2 (LR) or N2-1 - Body ground
      Always
      10 kΩ or higher
      E9-3 (LL) - N3-1
      Always
      Below 1 Ω
      E9-3 (LL) or N3-1 - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the turn signal flasher relay connector.

    5. Reconnect the rear turn signal light connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR TURN SIGNAL LIGHT ASSEMBLY - BODY GROUND)

11. INSPECT BULB (SIDE TURN SIGNAL LIGHT)

  1. E162323E01
    Remove the side turn signal light.

  1. Apply battery voltage to the terminals and check that the front turn signal light illuminates.

    OK:
    Measurement Condition
    Specified Condition
    Positive battery - Terminal 2
    Negative battery - Terminal 1
    Side turn signal light illuminates

  1. Reinstall the side turn signal light.



NG
REPLACE BULB (Click here)
OK


12. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER RELAY - SIDE TURN SIGNAL LIGHT)

  1. E162324E01
    Disconnect the E9 turn signal flasher relay connector.

  1. Disconnect the A33 and A36 side turn signal light connectors.

  1. Measure the resistance according value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E9-2 (LR) - A33-2
    Always
    Below 1 Ω
    E9-2 (LR) or A33-2 - Body ground
    Always
    10 kΩ or higher
    E9-3 (LL) - A36-2
    Always
    Below 1 Ω
    E9-3 (LL) or A36-2 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the turn signal flasher relay connector.

  1. Reconnect the side turn signal light connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SIDE TURN SIGNAL LIGHT - BODY GROUND)


← Rear Fog Light Circuit (from Nov 2010)Turn Signal Light Circuit (Nov 2010 – Jul 2014) →