2011-2016 FJ Cruiser · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Aug 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009


1. INSTALL GENERATOR DRIVE END FRAME BEARING

  1. A219663E01
    Using SST and a press, press in a new generator drive end frame bearing.
    SST
    09950-60010   (09951-00470)
    09950-70010   (09951-07100)

  1. A219664E01
    Fit the tabs on the retainer plate into the cutouts on the drive end frame to install the retainer plate.
    Text in Illustration 
    *1
    Tab
    *2
    Cutout

  1. Install the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }


2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Install the generator rotor assembly to the drive end frame.

  1. Place the generator washer on the generator rotor.


3. INSTALL GENERATOR COIL ASSEMBLY

  1. A128082E07
    Using a deep socket wrench (21 mm) and press, slowly press in the generator coil assembly.
    Text in Illustration 
    *1
    Deep socket wrench (21 mm)

  1. Install the 4 bolts.

    Torque:
    5.9 N*m{ 60 kgf*cm , 52 in.*lbf }


4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

  1. A079315E20
    While pushing the 2 brushes into the generator brush holder, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.
    Text in Illustration 
    *1
    Pin

  1. A219667E01
    Install the generator brush holder to the generator coil with the 2 screws.
    Text in Illustration 
    *1
    Pin

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

  1. Pull out the pin from the generator brush holder.


5. INSTALL GENERATOR TERMINAL INSULATOR

  1. A219668
    Install the terminal insulator to the generator coil.

    NOTICE:
    Pay attention to installation direction of the terminal insulator.


6. INSTALL GENERATOR REAR END COVER

  1. A220458
    Install the generator rear end cover to the generator coil with the 3 nuts.

    Torque:
    4.6 N*m{ 46 kgf*cm , 40 in.*lbf }

  1. A221621
    Install the cord clamp with the nut.

    Torque:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }


7. INSTALL GENERATOR CLUTCH PULLEY
  1. Temporarily install the generator with clutch pulley by hand.

  1. Mount the generator in a vise between aluminum plates.

  1. A219555E01
    Install SST (A) and (B) to the generator with clutch pulley as shown in the illustration.
    Text in Illustration 
    *1
    Rotor Shaft
    SST
    09820-63021  

    NOTICE:
    Securely attach SST to the generator with clutch pulley and generator rotor shaft.

  1. A219557E01
    Using a wrench to hold SST (A), turn SST (B) clockwise to tighten the generator with clutch pulley.
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

    Torque:
    without SST:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }
    with SST:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

    NOTICE:
    1. Be careful as the generator with clutch pulley or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.
    2. Use a torque wrench with a fulcrum length of 400 mm (15.7 in.).
    3. The torque value for use with SST is effective when SST is parallel to the torque wrench.

  1. Remove SST from the generator.

  1. Check that the generator with clutch pulley rotates smoothly.


8. INSTALL GENERATOR PULLEY CAP
  1. Install a new clutch pulley cap to the clutch pulley.

← REASSEMBLY (Jul 2007 – Jul 2009)INSTALLATION (Jul 2007 – Jul 2009) →