2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built from Nov 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 Aug 2012 – Oct 2012 from Nov 2012


1. INSTALL ULTRASONIC SENSOR RETAINER

  1. E135552E01
    Install the ultrasonic sensor retainer to the rear bumper.

    NOTICE:
    Do not damage the bumper with the snap when installing the retainer.

    HINT:
    When installing the retainer, align the keyhole and snap as shown in the illustration.


2. INSTALL ULTRASONIC SENSOR

  1. E161335
    Engage the 2 claws and install the ultrasonic sensor.

  1. Connect the sensor connector.


3. INSTALL REAR BUMPER EXTENSION MOULDING LH
  1. Clean the attachment surface.

    1. Using an infrared light, heat the adhesive remaining on the rear bumper cover.

      Heating Temperature:
      Item
      Temperature
      Rear Bumper Cover
      40 to 60°C (104 to 140°F)

      CAUTION:
      Do not burn yourself on the hot rear bumper cover or with the infrared light.

      NOTICE:
      Do not heat the rear bumper cover excessively.

    2. Using a piece of cloth, rub the remaining adhesive off the rear bumper cover.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Remove the release paper from the rear bumper extension mounting bracket.

  1. B309429E01
    Install the rear bumper extension mounting bracket as shown in the illustration.
    Text in Illustration 
    *1
    Double-sided Tape

    NOTICE:
    Thoroughly press the rear bumper extension mounting bracket to ensure that it adheres.


4. INSTALL REAR BUMPER EXTENSION MOULDING RH

HINT:
Use the same procedure as for the LH side.


5. INSTALL REAR FOG LIGHT ASSEMBLY LH

E161251
  1. Install the rear fog light with the 2 screws.

  1. Connect the 2 connectors and wire harness clamp.


6. INSTALL REAR FOG LIGHT ASSEMBLY RH

E161252
  1. Install the rear fog light with the 2 screws.

  1. Connect the 2 connectors and wire harness clamp.


7. INSTALL REAR BUMPER SIDE RETAINER RH

E161885
  1. Install the rear bumper extension retainer with the 3 screws.


8. INSTALL REAR BUMPER SIDE RETAINER LH

HINT:
Use the same procedure as for the RH side.


9. INSTALL NO. 8 FLOOR WIRE

  1. Engage the clamps.

    B332238E01

    Text in Illustration 
    *A
    for Type A
    *B
    for Type B

  1. Connect the connectors.


10. INSTALL REAR BUMPER COVER
  1. Engage the 6 claws and the 2 clips and install the rear bumper cover.

  1. Engage the wire harness clamp, and connect the connector.

  1. B332240E02
    Install the 7 bolts and the 2 screws.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *3
    Screw

    Torque:
    for bolt A:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    for bolt B:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for screw:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. Install the clip.

  1. Remove the protective tape.

← INSTALLATION (Aug 2012 – Oct 2012)COMPONENTS (Jul 2007 – Oct 2010) →