REMOVAL
Removal / installation · Vehicles built Jul 2007 – Oct 2010
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012
- HINT:
- The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.
| 1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
|
| 2.
REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH
|
 |
- Pull the rear seatback lock release button and tilt the rear seatback forward.
Disengage the 10 clips and remove the rear seatback board carpet.
| 3.
REMOVE REAR SEATBACK ASSEMBLY RH
|
 |
- Pull up the rear seatback.
Remove the bolt and the anchor plate of the rear center seat outer belt.
- Remove the rear seat inner belt from the rear seatback holder.
Pull the rear seatback lock release button and tilt the rear seatback forward.
Remove the 2 bolts.
Disengage the hook and remove the rear seatback.
| 4.
REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH
|
 |
- Pull the rear seatback lock release button and tilt the rear seatback forward.
Disengage the 8 clips and remove the rear seatback board carpet.
| 5.
REMOVE REAR SEATBACK ASSEMBLY LH
|
 |
- Remove the rear center seat inner belt from the rear seatback holder.
Remove the 2 bolts.
Disengage the hook and remove the rear seatback.
| 6.
REMOVE REAR FLOOR BOARD
|
 |
- Remove the bolt and the luggage hold belt striker.
- HINT:
- Use the same procedure for both sides.
- Disengage the clip and the claw and remove the rear floor board.
| 7.
REMOVE REAR FLOOR MAT SUPPORT PLATE
|
 |
- Remove the 5 screws.
- Disengage the 11 claws and remove the rear floor mat support plate.
| 8.
REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY
|
 |
- HINT:
- Use the same procedure for both sides.
- Remove the cap.
Remove the bolt and the luggage hold belt striker.
| 9.
REMOVE REAR FLOOR MAT ASSEMBLY
|
 |
- Using a clip remover, remove the 2 clips and the rear floor mat.
| 10.
REMOVE FRONT DOOR SCUFF PLATE RH
|
 |
- Disengage the 14 claws and remove the front door scuff plate.
| 11.
REMOVE FRONT DOOR SCUFF PLATE LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 12.
REMOVE ACCESS DOOR SCUFF PLATE RH
|
 |
- Disengage the 6 claws and remove the access door scuff plate.
| 13.
REMOVE ACCESS DOOR SCUFF PLATE LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 14.
REMOVE FRONT FLOOR FOOTREST
|
 |
- Disengage the 4 claws and remove the front floor footrest.
| 15.
REMOVE FOOTREST CLIP
|
 |
- Remove the 2 footrest clips.
| 16.
REMOVE COWL SIDE TRIM BOARD RH
|
 |
- Remove the clip.
Disengage the 2 claws and remove the cowl side trim board.
| 17.
REMOVE COWL SIDE TRIM BOARD LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 18.
REMOVE ROOF SIDE INNER GARNISH COVER RH
|
 |
- HINT:
- Use the same procedure for both sides.
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the roof side inner garnish cover.
| 19.
REMOVE ROOF SIDE INNER GARNISH COVER LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 20.
REMOVE ROOF SIDE RAIL GARNISH RH
|
 |
- Remove the 2 bolts.
Disengage the 2 claws and remove the roof side rail garnish.
| 21.
REMOVE ROOF SIDE RAIL GARNISH LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 22.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
|
 |
- Remove the front door opening trim weatherstrip.
| 23.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 24.
REMOVE ASSIST GRIP PLUG
|
 |
- HINT:
- Use the same procedure to remove all the assist grip plugs.
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip plug.
| 25.
REMOVE ASSIST GRIP ASSEMBLY
|
 |
- HINT:
- Use the same procedure to remove all the assist grips.
Remove the 2 screws and the assist grip.
| 26.
REMOVE VISOR SUB-ASSEMBLY RH
|
 |
Disengage the 2 claws and remove the visor sub-assembly.
| 27.
REMOVE VISOR SUB-ASSEMBLY LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 28.
REMOVE FRONT PILLAR GARNISH RH
|
 |
- Disengage the 2 clips and the claw and remove the front pillar garnish.
| 29.
REMOVE FRONT PILLAR GARNISH LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 30.
REMOVE DECK SIDE GARNISH (w/ Woofer)
|
 |
- Disengage the 6 claws and remove the rear deck side garnish.
| 31.
REMOVE SPEAKER MOUNTING COVER (w/ Woofer)
|
 |
- Disengage the 8 clips and remove the speaker mounting cover.
| 32.
REMOVE AMPLIFIER BOX SPEAKER ASSEMBLY (w/ Woofer)
|
 |
- Disconnect the speaker connector.
Remove the 4 screws and the amplifier box speaker.
| 33.
REMOVE PACKAGE HOLDER NET HOOK
|
 |
- HINT:
- Use the same procedure to remove all the package holder net hooks.
Remove the screw and the package holder net hook.
| 34.
REMOVE QUARTER TRIM POCKET TRAY (w/o Woofer)
|
 |
- Disengage the 7 claws and remove the quarter trim pocket tray.
| 35.
REMOVE SIDE TRIM COVER (w/o Woofer)
|
 |
- Disengage the 8 claws and remove the side trim cover.
| 36.
REMOVE QUARTER TRIM POCKET (w/o Woofer)
|
 |
- Disengage the 6 claws and remove the quarter trim pocket.
| 37.
REMOVE LAP BELT OUTER ANCHOR COVER
|
 |
- HINT:
- Use the same procedure for both sides.
Disengage the 3 claws and remove the lap belt outer anchor cover.
| 38.
REMOVE REAR SEAT OUTER BELT ASSEMBLY RH
|
 |
- Remove the bolt and the anchor plate.
| 39.
REMOVE REAR SEAT OUTER BELT ASSEMBLY LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 40.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
|
 |
- Remove the 4 screws.
- Disengage the 6 clips and the 8 claws and remove the deck trim side panel.
| 41.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
|
 |
- Remove the 3 screws.
- Disengage the 6 clips and the 8 claws and remove the deck trim side panel.
| 42.
REMOVE ROOF SIDE INNER GARNISH RH
|
 |
- Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
- Remove the bolt and the clip.
Disengage the 7 clips and the claw and remove the roof side inner garnish.
Pass the rear seat outer belt through the slit in the roof side inner garnish.
| 43.
REMOVE ROOF SIDE INNER GARNISH LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 44.
REMOVE ROOF HEADLINING HOLE PLUG (w/ Curtain Shield Airbag)
|
 |
- HINT:
- Use the same procedure for both sides.
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and open the cover.
- Remove the bolt.
Disengage the claw and remove the roof headlining hole plug.
| 45.
REMOVE COAT HOOK
|
 |
- HINT:
- Use the same procedure for both sides.
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
- Remove the bolt and the coat hook.
| 46.
REMOVE VISOR ASSEMBLY RH
|
 |
- Remove the visor support shaft from the visor holder.
Remove the 2 screws and the visor.
| 47.
REMOVE VISOR ASSEMBLY LH
|
 |
- HINT:
- Use the same procedure as for the RH side.
| 48.
REMOVE VISOR HOLDER
|
 |
- HINT:
- Use the same procedure for both sides.
Disengage the 2 claws by turning the visor counterclockwise between 60 to 120° and remove the visor holder.
- HINT:
- The claw may be damaged during removal. However, it is reusable because this does not effect its function.
| 49.
REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER
|
 |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the inner rear view mirror stay holder cover.
| 50.
REMOVE INNER REAR VIEW MIRROR ASSEMBLY
|
 |
Remove the 2 screws and remove the inner rear view mirror.
| 51.
REMOVE ROOM LIGHT ASSEMBLY
|
 |
- HINT:
- The procedure described below is for the front side. Use the same procedure for both the front and rear sides, unless otherwise specified.
- Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens.
- Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.
- HINT:
- Use the same procedure as for the opposite side.
- Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light.
- for Front Side:
Remove the 2 wire harnesses from the 2 claws of the room light.
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base.
- for Rear Side:
Remove the wire harness from the claw of the room light.
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base.
| 52.
REMOVE ROOF HEADLINING |
 |
- Using a clip remover, remove the 3 clamps and the connector.
Using a clip remover, remove the 4 clips.


| 53.
REMOVE ROOF SPEAKER ASSEMBLY |
 |
- Remove the hole cover.
- Disconnect the speaker connector.
Loosen the screw.
- Remove the roof speaker by turning it in the direction of the arrow shown in the illustration.