REASSEMBLY
Removal / installation · Vehicles built Jul 2007 – Oct 2010
Versions by build date: Jul 2007 – Oct 2010 from Nov 2010
- CAUTION:
- Wear protective gloves. Sharp surfaces on the rear seat cushion frame and the rear seatback frame could cause injuries to your hands.
| 1.
INSTALL REAR SEATBACK COVER |
 |
- Using hog ring pliers, install the rear seatback cover with 8 new hog rings.
- NOTICE:
- Do not soil or scratch the rear seatback cover.
- When installing the hog rings, minimize wrinkles as far as possible.
Pass the hook of the rear seatback cover through the slit in the rear seatback pad.
| 2.
INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY
|
 |
- Hook the stay of the retractor onto the 2 rear seatback frame hooks and install the retractor with the nut.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
Check that the ELR locks.
- NOTICE:
- Perform the check with the front seat outer belt installed.
With the belt installed, check that the belt locks when it pulled out quickly.
If the operation is not as specified, replace the rear seat outer belt.
| 3.
INSTALL REAR SEATBACK LOCK ASSEMBLY |
 |
- Install the rear seatback lock with the 2 bolts.
-
Torque:
- 18 N*m{
185 kgf*cm
, 13 ft.*lbf
}
| 4.
INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY |
 |
- Install the rear seatback frame.
- Using hog ring pliers, install 17 new hog rings.
- Install the belt of the rear center seat outer belt into the rear seatback cover band.
| 5.
INSTALL REAR SEATBACK STOP BUTTON GROMMET |
 |
- Engage the 2 claws and install the rear seatback stop button grommet.
| 6.
INSTALL REAR SEATBACK LOCK RELEASE BUTTON |
 |
- Install rear seatback lock release button.
| 7.
INSTALL REAR SEAT HEADREST SUPPORT |
 |
- HINT:
- Use the same procedure to install all the rear seat headrest supports.
Align the protruding portion of the rear seat headrest support with the installation groove of the rear seatback frame.
Engage the 2 claws and install the rear seat headrest support.
| 8.
INSTALL TETHER ANCHOR COVER |
 |
- HINT:
- Use the same procedure for both sides.
Engage the 3 claws and install the tether anchor cover.
- Engage the 2 claws and close the cover.
| 9.
INSTALL REAR SEATBACK LOCK COVER |
 |
- Engage the claw and install the rear seatback lock cover.
Tighten the screw.
| 10.
INSTALL REAR SEAT SHOULDER BELT COVER |
 |
- Engage the 4 claws and install the rear seat shoulder belt cover.
| 11.
INSTALL REAR CENTER SEAT HEADREST ASSEMBLY |
 |
- Push the lock button of the rear seat headrest support and install the rear seat headrest.
| 12.
INSTALL REAR SEAT HEADREST ASSEMBLY |
 |
- Push the lock button of the rear seat headrest support and install the rear seat headrest.
| 13.
INSTALL REAR SEAT CUSHION COVER |
 |
- Using hog ring pliers, install the rear seat cushion cover with 10 new hog rings.
- NOTICE:
- Do not soil or scratch the rear seat cushion cover.
- When installing the hog rings, minimize wrinkles as far as possible.
| 14.
INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY |
 |
- Engage the hook and install the rear seat cushion frame.
| 15.
INSTALL REAR SEAT CUSHION STOPPER |
 |
- Install the rear seat cushion stopper with the screw.
| 16.
INSTALL REAR SEAT CUSHION UNDER COVER |
 |
- Insert the rear seat cushion stopper into the slit of the rear seat cushion under cover.
Install the rear seat cushion under cover with the 7 clips.
Install the rear seat cushion stopper into the rear seat cushion cover band.
| 17.
INSTALL REAR SEAT CUSHION HINGE SUB-ASSEMBLY |
 |
- HINT:
- Use the same procedure for both sides.
Engage the hook and install the rear seat cushion hinge.
Install the rear seat cushion hinge with the bolt.
-
Torque:
- 18 N*m{
185 kgf*cm
, 13 ft.*lbf
}