2011-2016 FJ Cruiser · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

CAUTION:
Wear protective gloves. Sharp surfaces on the rear seat cushion frame and the rear seatback frame could cause injuries to your hands.


1. INSTALL REAR SEATBACK COVER

  1. B130775E02
    Using hog ring pliers, install the rear seatback cover with 8 new hog rings.
    Text in Illustration 
    *1
    New Hog Ring
    *2
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the rear seatback cover.
    2. When installing the hog rings, minimize wrinkles as far as possible.

  1. Pass the hook of the rear seatback cover through the slit in the rear seatback pad.


2. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY

  1. B135155
    Hook the stay of the retractor onto the 2 rear seatback frame hooks and install the retractor with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check that the ELR locks.

    NOTICE:
    Perform the check with the front seat outer belt installed.


    1. With the belt installed, check that the belt locks when it pulled out quickly.
      If the operation is not as specified, replace the rear seat outer belt.


3. INSTALL REAR SEATBACK LOCK ASSEMBLY

  1. B130772
    Install the rear seatback lock with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


4. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY

  1. B130768
    Install the rear seatback frame.

  1. B130767E02
    Using hog ring pliers, install 17 new hog rings.
    Text in Illustration 
    *1
    New Hog Ring
    *2
    Hog Ring Pliers

  1. B135129E02
    Install the belt of the rear center seat outer belt into the rear seatback cover band.
    Text in Illustration 
    *1
    Band


5. INSTALL REAR SEATBACK STOP BUTTON GROMMET

  1. B130771
    Engage the 2 claws and install the rear seatback stop button grommet.


6. INSTALL REAR SEATBACK LOCK RELEASE BUTTON

  1. B130773
    Install rear seatback lock release button.


7. INSTALL REAR SEAT HEADREST SUPPORT

B130770E02
Text in Illustration 
*a
Protrusion

HINT:
Use the same procedure to install all the rear seat headrest supports.

  1. Align the protruding portion of the rear seat headrest support with the installation groove of the rear seatback frame.

  1. Engage the 2 claws and install the rear seat headrest support.


8. INSTALL TETHER ANCHOR COVER

B130765

HINT:
Use the same procedure for both sides.

  1. Engage the 3 claws and install the tether anchor cover.

  1. B130763
    Engage the 2 claws and close the cover.


9. INSTALL REAR SEATBACK LOCK COVER

  1. B130761
    Engage the claw and install the rear seatback lock cover.

  1. Tighten the screw.


10. INSTALL REAR SEAT SHOULDER BELT COVER

  1. B267855
    Engage the 4 claws and install the rear seat shoulder belt cover.


11. INSTALL SHOULDER BELT ANCHOR COVER

  1. B267854
    Engage the 2gides and 2 claws, install the shoulder belt anchor cover.


12. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY

  1. B130760E02
    Push the lock button of the rear seat headrest support and install the rear seat headrest.
    Text in Illustration 
    *1
    Lock Button


13. INSTALL REAR SEAT HEADREST ASSEMBLY

  1. B130759E02
    Push the lock button of the rear seat headrest support and install the rear seat headrest.
    Text in Illustration 
    *1
    Lock Button


14. INSTALL REAR SEAT CUSHION COVER

  1. B130757E02
    Using hog ring pliers, install the rear seat cushion cover with 10 new hog rings.
    Text in Illustration 
    *1
    New Hog Ring
    *2
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the rear seat cushion cover.
    2. When installing the hog rings, minimize wrinkles as far as possible.


15. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY

  1. B130755
    Engage the hook and install the rear seat cushion frame.


16. INSTALL REAR SEAT CUSHION STOPPER

  1. B130754
    Install the rear seat cushion stopper with the screw.


17. INSTALL REAR SEAT CUSHION UNDER COVER

  1. B130753E02
    Insert the rear seat cushion stopper into the slit of the rear seat cushion under cover.
    Text in Illustration 
    *1
    Band

  1. Install the rear seat cushion under cover with the 7 clips.

  1. Install the rear seat cushion stopper into the rear seat cushion cover band.


18. INSTALL REAR SEAT CUSHION HINGE SUB-ASSEMBLY

B130752

HINT:
Use the same procedure for both sides.

  1. Engage the hook and install the rear seat cushion hinge.

  1. Install the rear seat cushion hinge with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

← REASSEMBLY (Jul 2007 – Oct 2010)INSTALLATION (from Jul 2007) →