2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL RADIO ANTENNA HOLDER ASSEMBLY
  1. Hook the body side bracket onto the hook of the radio antenna holder and provisionally install the radio antenna holder.

  1. Insert the feeder line through the body hole and install the grommet.

  1. B135036E01
    Tighten bolt A and then bolt B.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Install the 3 clamps and the connector.

  1. Connect the connector.


2. INSTALL FENDER SPLASH REAR SHIELD SUB-ASSEMBLY
  1. Install the fender splash rear shield with the 3 clips.


3. INSTALL FRONT FENDER SIDE UPPER PANEL
  1. Install the 4 new clips on the front fender side panel upper RH.

  1. B210064
    Engage the 4 clips and install the front fender side panel upper RH.


4. INSTALL ANTENNA ORNAMENT

  1. E127861E02
    Press in the antenna ornament in the direction shown in the illustration.


5. INSTALL RADIO ANTENNA POLE SUB-ASSEMBLY

  1. E148353E01
    Install the radio antenna pole sub-assembly by hand until fully seated.
    Text in Illustration 
    *a
    1/8 turn (20 to 45 degrees)

  1. Using a 8 mm (5/16 inch) wrench, fully tighten the radio antenna pole about 1/8 turn (20 to 45 degrees) by turning it clockwise.

    NOTICE:
    1. Do not over tighten. Tighten with finger, not hand.
    2. Do not use pliers to tighten the radio antenna pole as it can leave marks on the radio antenna pole surface.
    3. The antenna pole cannot be hand tightened to the proper specification.

    Torque:
    3.3 N*m{ 34 kgf*cm , 29 in.*lbf }


6. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY

HINT:
Use the same procedure as for the LH side (Click here).


7. INSTALL FRONT BUMPER SIDE SUPPORT

HINT:
Use the same procedure as for the LH side (Click here).


8. INSTALL FRONT FENDER MUDGUARD

HINT:
Use the same procedure as for the LH side (Click here).


9. INSTALL ROCKER PANEL MOULDING

HINT:
Use the same procedure as for the LH side (Click here).


10. INSTALL SIDE STEP SUB-ASSEMBLY (w/ Side Step)

HINT:
Use the same procedure as for the LH side (Click here).


11. INSTALL FRONT BUMPER COVER

  1. B134733
    Engage the 2 claws and install the front bumper cover.

  1. B134732
    Tighten the 8 screws and the 4 bolts.

    Torque:
    3.0 N*m{ 30 kgf*cm , 27 in.*lbf } for screw
    8.0 N*m{ 80 kgf*cm , 71 in.*lbf } for bolt

  1. B138606
    Install the 5 clips.

  1. B134730E01
    Remove the protective tape.


12. INSTALL RADIATOR GRILLE
  1. Engage the 5 clips and install the radiator grille.

  1. Install the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. Install the 2 clips.


13. INSTALL FRONT PILLAR GARNISH
  1. w/ Assist Grip:

    1. Engage the guide and the 2 clips and install the front pillar garnish.

  1. w/o Assist Grip:

    1. Engage the guide and the 2 clips and install the front pillar garnish.

    2. Install the bolt.

    3. B271491
      Engage the claw and close the cover.


14. INSTALL ASSIST GRIP ASSEMBLY (w/ Assist Grip)
  1. Install the assist grip with the 2 screws.


15. INSTALL ASSIST GRIP PLUG (w/ Assist Grip)

B134997

HINT:
Use the same procedure for both sides.

  1. Engage the 2 claws and install the assist grip plug.


16. INSTALL DRIVER SIDE JUNCTION BLOCK (for RHD)

  1. E218717
    Connect the connectors on the LH side.

  1. Install the instrument panel junction block with the 3 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Engage the guides and connect the connectors on the front side.


17. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (for RHD)
  1. Connect the connectors.

  1. Engage the 8 clips and 4 guides and install the lower instrument panel finish panel.

  1. Install the 2 <E> bolts.


18. INSTALL INSTRUMENT PANEL FINISH PLATE (for RHD)

  1. E149563E03
    Install the instrument panel finish plate.
    Text in Illustration 
    *1
    Instrument Panel Finish Plate


19. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for RHD)
  1. Engage the 3 claws and install the fuel lid lock open lever.


20. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for RHD)
  1. Engage the 3 claws and install the hood lock control lever.


21. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (for RHD)
  1. Engage the 4 clips and 2 claws and install the instrument panel register.


22. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP
  1. Install the front door opening trim weatherstrip.


23. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (for LHD)

  1. B271481
    Install the glove compartment door assembly with the 3 hinges while holding it horizontal.

  1. Slightly flex the upper part of the glove compartment door assembly, and install the glove compartment door assembly.

  1. Install the glove compartment door stoppers onto the glove compartment door.

← INSTALLATION (Aug 2012 – Jul 2013)INSTALLATION (from Aug 2014) →