2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL RADIO ANTENNA HOLDER ASSEMBLY

  1. B135036
    Hook the body side bracket onto the hook of the radio antenna holder and provisionally install the radio antenna holder.

  1. Insert the feeder line through the body hole and install the grommet.

  1. Tighten bolt A and then bolt B.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. B135035
    Install the 2 clamps and the connector.

  1. Connect the connector.


2. INSTALL FENDER SPLASH REAR SHIELD SUB-ASSEMBLY

  1. B135034
    Install the fender splash rear shield with the 3 clips.


3. INSTALL FRONT FENDER SIDE UPPER PANEL
  1. Install the 4 new clips on the front fender side panel upper RH.

  1. B210064
    Engage the 4 clips and install the front fender side panel upper RH.


4. INSTALL ANTENNA ORNAMENT

  1. E127861E02
    Press in the antenna ornament in the direction shown in the illustration.


5. INSTALL RADIO ANTENNA POLE SUB-ASSEMBLY

B138406E01
  1. Install the radio antenna pole by turning it in the direction of the arrow shown in the illustration.

    Torque:
    3.3 N*m{ 35 kgf*cm , 29 in.*lbf }

    NOTICE:
    Use a short wrench, tighten with your finger, not your hand.


6. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY

HINT:
Use the same procedure as for the LH side (Click here).


7. INSTALL FRONT BUMPER SIDE SUPPORT

HINT:
Use the same procedure as for the LH side (Click here).


8. INSTALL FRONT FENDER MUDGUARD

HINT:
Use the same procedure as for the LH side (Click here).


9. INSTALL ROCKER PANEL MOULDING

HINT:
Use the same procedure as for the LH side (Click here).


10. INSTALL SIDE STEP SUB-ASSEMBLY (w/ Side Step)

HINT:
Use the same procedure as for the LH side (Click here).


11. INSTALL FRONT BUMPER COVER

  1. B134733
    Engage the 2 claws and install the front bumper cover.

  1. B134732
    Tighten the 8 screws and the 4 bolts.

    Torque:
    3.0 N*m{ 30 kgf*cm , 27 in.*lbf } for screw
    8.0 N*m{ 80 kgf*cm , 71 in.*lbf } for bolt

  1. B138606
    Install the 5 clips.

  1. B134730E01
    Remove the protective tape.


12. INSTALL RADIATOR GRILLE

  1. B134729
    Engage the 5 clips and install the radiator grille.

  1. Tighten the 2 screws.

    Torque:
    3.0 N*m{ 30 kgf*cm , 27 in.*lbf }

  1. Install the 2 clips.


13. INSTALL FRONT PILLAR GARNISH

  1. B130608
    Engage the claw and the 2 clips and install the front pillar garnish.


14. INSTALL ASSIST GRIP ASSEMBLY

  1. B134998
    Install the assist grip with the 2 screws.


15. INSTALL ASSIST GRIP PLUG

B134997

HINT:
Use the same procedure for both sides.

  1. Engage the 2 claws and install the assist grip plug.


16. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP

  1. B138422
    Install the front door opening trim weatherstrip.


17. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

  1. B133856
    Install the glove compartment door assembly with the 3 hinges while holding it horizontal.

  1. B133854E01
    Slightly flex the upper part of the glove compartment door assembly, and install the glove compartment door assembly.

  1. Install the glove compartment door stoppers onto the glove compartment door.


18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }

← REMOVAL (from Aug 2014)INSTALLATION (Nov 2010 – Jul 2011) →