2011-2016 FJ Cruiser · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Aug 2009 – Oct 2010

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010


1. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install a new gasket onto the exhaust manifold RH.

  1. A128851
    Install the exhaust front pipe with new 2 nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }

  1. A128852E01
    Install a new gasket onto the front exhaust pipe.

    1. Using a wooden block and plastic-faced hammer, tap in a new gasket until it is flush with the front exhaust pipe end.

      NOTICE:
      1. Make sure that the gasket is in the correct direction when installing.
      2. Do not reuse the removed gasket.
      3. Do not push in the gasket with the exhaust pipe when connecting it.


2. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY
  1. Install a new gasket onto the exhaust manifold LH.

  1. Install a new gasket onto the No. 2 front exhaust pipe.

  1. A129938
    Install the front No. 2 exhaust pipe with 2 new nuts and 2 bolts and exhaust pipe support.

    Torque:
    Nut:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }
    Bolt:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

  1. A129939
    Install the exhaust pipe stopper bracket with the 2 bolts (for 4WD).

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


3. INSTALL CENTER EXHAUST PIPE ASSEMBLY

  1. A128853
    Check the free length.

    1. Using vernier calipers, measure the free length of the compression spring.

      Minimum:
      40.5mm (1.594 in.)

      If the free length is less that the minimum, replace the compression spring.

  1. A129937
    Install the center exhaust pipe onto the 4 exhaust pipe supports.

  1. Install the center exhaust pipe with the 2 bolts and 2 springs.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


4. INSTALL TAIL EXHAUST PIPE ASSEMBLY

  1. A129936
    Install a new gasket onto the center exhaust pipe.

  1. Install the tail exhaust pipe with the 2 bolts and exhaust pipe support.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }


5. INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

  1. A158663
    Temporarily install the sensor to the exhaust pipe by hand.

  1. A229766E01
    Using SST, tighten the sensor.
    Text in Illustration 
    *a
    Fulcrum Length
    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).
    2. The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 300 mm (11.81 in.) (Click here).
    3. This torque value is effective when SST is parallel to the torque wrench.

  1. Connect the sensor connector.


6. INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)

  1. A158663
    Temporarily install the sensor to the exhaust pipe by hand.

  1. A223690E02
    Using SST, tighten the sensor.
    Text in Illustration 
    *a
    Fulcrum Length
    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).
    2. The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 300 mm (11.81 in.) (Click here).
    3. This torque value is effective when SST is parallel to the torque wrench.

  1. Connect the sensor connector.


7. INSPECT FOR EXHAUST GAS LEAK
← INSTALLATION (Jul 2007 – Jul 2009)INSTALLATION (from Nov 2010) →