2011-2016 FJ Cruiser · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009


INSPECT GENERATOR VOLTAGE REGULATOR ASSEMBLY (for 80A Type)

  1. A059143E03
    Measure the resistance between the voltage regulator terminals (F) and (B).

    Standard resistance:
    Below 1Ω or more than 10kΩ

    HINT:
    When the ohmmeter leads are initially touched to the regulator, one of the above values will be output. When the leads are reversed, the reading will change to the other reading.
    If the result is not as specified, replace the voltage regulator.

  1. A059144E03
    Measure the resistance between the voltage regulator terminals (F) and (E).

    Standard resistance:
    Below 1Ω or more than 10kΩ

    HINT:
    When the ohmmeter leads are initially touched to the regulator, one of the above values will be output. When the leads are reversed, the reading will change to the other reading.
    If the result is not as specified, replace the voltage regulator.


INSPECT GENERATOR BRUSH HOLDER ASSEMBLY

A138091E01
  1. Using vernier calipers, measure the exposed brush length.

    Standard exposed brush length:
    10.5 mm (0.413 in.)

    Minimum exposed brush length:
    4.5 mm (0.177 in.)

    If the exposed brush length is less than the minimum, replace the brush holder.


INSPECT GENERATOR HOLDER WITH RECTIFIER (for 80A Type)

  1. A082701E03
    Inspect the positive (+) rectifier.

    1. Using an ohmmeter, connect one tester probe to the positive (+) terminal and the other to each rectifier terminal.

    2. Reverse the polarity of the tester probes and repeat the step above.

    3. Check that one shows an resistance of below 1 Ω and the other shows a resistance of 10 kΩ or higher.
      If the result is not as specified, replace the generator holder with rectifier.

  1. A082702E03
    Inspect the negative (-) rectifier.

    1. Using an ohmmeter, connect one tester probe to the negative (-) terminal and the other to each rectifier terminal.

    2. Reverse the polarity of the tester probes and repeat the step above.

    3. Check that one shows an resistance of below 1 Ω and the other shows a resistance of 10 kΩ or higher.
      If the result is not as specified, replace the generator holder with rectifier.


INSPECT GENERATOR ROTOR ASSEMBLY

A138092E03
  1. Check the rotor for an open circuit.

    1. Using an ohmmeter, measure the resistance between the slip rings.

      Standard resistance:
      for 100A Type:
      2.3 to 2.7 Ω at 20°C (68°F)
      for 80A Type:
      1.7 to 2.1 Ω at 20°C (68°F)

      If the resistance is not as specified, replace the rotor.

  1. A138093E01
    Check the rotor for ground.

    1. Using an ohmmeter, check the resistance between the slip ring and rotor.

      Standard resistance:
      10 kΩ or higher

      If the resistance is not as specified, replace the rotor.

  1. Inspect the slip rings.

    1. Check that the slip rings are not rough or scored.
      If rough or scored, replace the rotor assembly.

    2. A138095E01
      Using vernier calipers, measure the slip ring diameter.

      Standard diameter:
      14.2 to 14.4 mm (0.559 to 0.567 in.)

      Minimum diameter:
      14.0 mm (0.551 in.)

      If the diameter is less than the minimum, replace the rotor.


INSPECT GENERATOR ROTOR BEARING

A138094
  1. Check that the bearing is not rough or worn.
    If necessary, replace the generator rotor assembly.


INSPECT GENERATOR DRIVE END FRAME BEARING

A075681
  1. Check that the bearing is not rough or worn.
    If necessary, replace the bearing.


INSPECT RECTIFIER END FRAME (for 80A Type)

  1. A172205E01
    Check the stator coil for an open circuit.

    1. Measure the resistance between the coil leads.

      Standard resistance:
      Below 1 Ω

      If the result is not as specified, replace the rectifier end frame.

  1. A172206E01
    Check the stator for an ground.

    1. Measure the resistance between the coil lead and drive end frame.

      Standard resistance:
      10 Ω or higher

      If the result is not as specified, replace the rectifier end frame.

← DISASSEMBLY (from Aug 2009)INSPECTION (from Aug 2009) →