2011-2016 FJ Cruiser · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 from Aug 2009


1. REMOVE GENERATOR PULLEY

A075664E08
SST
09820-63010   (09820-06010, 09820-06020)
HINT 
SST 1-A and B
09820 - 06010
SST 2
09820 - 06020
  1. Hold SST 1-A with a torque wrench, and tighten SST 1-B clockwise with the specified torque.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

    NOTICE:
    Check that SST is secured to the rotor shaft.

  1. A075665E03
    Mount SST 2 in a vise.

  1. Insert SST 1-A and B into SST 2, and attach the pulley nut to SST 2.

  1. A075666E02
    To loosen the pulley nut, turn SST 1-A in the direction shown in the illustration.

    NOTICE:
    To prevent damage to the rotor shaft, do not loosen the pulley nut more than one-half turn.

  1. Remove the generator from SST 2.

  1. A075667E04
    Turn SST 1-B, and remove SST 1-A and B.

  1. Remove the pulley nut and pulley.


2. REMOVE GENERATOR REAR END COVER (for 100A Type)

A075668E01
  1. Place the generator on the pulley.

  1. Remove the 3 nuts and the rear end cover.


3. REMOVE TERMINAL INSULATOR (for 80A Type)
  1. Remove the nut and terminal insulator.


4. REMOVE GENERATOR REAR END COVER (for 80A Type)

  1. A121962
    Remove the bolt, 3 nuts, plate terminal and rear end cover.


5. REMOVE TERMINAL INSULATOR (for 100A Type)

A138090
  1. Remove the terminal insulator.


6. REMOVE GENERATOR BRUSH HOLDER ASSEMBLY (for 100A Type)

A137216
  1. Remove the 2 screws and the brush holder.


7. REMOVE GENERATOR BRUSH HOLDER ASSEMBLY (for 80A Type)

A172184
  1. Remove the brush holder cover from the brush holder.

  1. Remove the 2 screws and brush holder.


8. REMOVE GENERATOR VOLTAGE REGULATOR ASSEMBLY (for 80A Type)

  1. A172183
    Remove the 3 screws and voltage regulator.


9. REMOVE GENERATOR HOLDER WITH RECTIFIER (for 80A Type)

  1. A121964
    Remove the 3 screws and generator holder with rectifier.


10. REMOVE GENERATOR COIL ASSEMBLY (for 100A Type)

A075671
  1. Remove the 4 bolts.

  1. A075672E01
    Using SST, remove the coil.
    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


11. REMOVE GENERATOR DRIVE FRAME ASSEMBLY (for 80A Type)
  1. Remove the 3 rubber insulators.

  1. Remove the seal plate.

  1. A121965
    Remove the 4 nuts.

  1. A121966E02
    Using SST, remove the rectifier end frame from the generator drive frame.
    SST
    09286-46011  


12. REMOVE GENERATOR ROTOR ASSEMBLY

A075673
  1. Remove the washer and rotor.

    NOTICE:
    Do not drop the rotor.


13. REMOVE GENERATOR DRIVE END FRAME BEARING (for 100A Type)

A075682
  1. Remove the 4 screws and the retainer plate.

  1. A075683E01
    Using SST, tap out the bearing.
    SST
    09950-60010   (09951-00250)
    09950-70010   (09951-07100)

← REMOVAL (from Aug 2014)DISASSEMBLY (from Aug 2009) →