2011-2016 FJ Cruiser · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Nov 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Oct 2012 from Nov 2012


1. INSTALL NO. 4 FUEL TANK BAND BRACKET (for Double Tank Type)
  1. for LH Side:

    1. Install the No. 4 fuel tank band bracket with the 4 bolts.

      Torque:
      40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    2. Engage the 3 clamps and connect the wire harness.

  1. for RH Side:

    1. Install the No. 4 fuel tank band bracket with the 4 bolts.

      Torque:
      40 N*m{ 408 kgf*cm , 30 ft.*lbf }


2. INSTALL FUEL SUB TANK SUB-ASSEMBLY (for Double Tank Type)
(Click here)

3. INSTALL REAR BUMPER SIDE SUPPORT SUB-ASSEMBLY LH (for Single Tank Type)
  1. Align the 2 locating guides with the hole and install the rear bumper side support sub-assembly LH with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


4. INSTALL REAR BUMPER SIDE SUPPORT SUB-ASSEMBLY RH (for Single Tank Type)

HINT:
Use the same procedure as for the LH side.


5. INSTALL REAR BUMPER BAR BRACKET LH
  1. Insert the hook into the body hole and install the rear bumper bar bracket LH with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


6. INSTALL REAR BUMPER BAR BRACKET RH

HINT:
Use the same procedure as for the LH side.


7. INSTALL REAR BUMPER SIDE STAY LH

  1. B271869
    Insert the hook into the body hole and install the rear bumper side stay LH with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


8. INSTALL REAR BUMPER SIDE STAY RH

HINT:
Use the same procedure as for the LH side.


9. INSTALL REAR BUMPER ENERGY ABSORBER
  1. Engage the 2 claws and install the rear bumper energy absorber.


10. INSTALL REAR BUMPER UPPER RETAINER LH
  1. Engage the 3 claws and install the rear bumper upper retainer LH.

  1. Install the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }


11. INSTALL REAR BUMPER UPPER RETAINER RH

HINT:
Use the same procedure as for the LH side.


12. INSTALL REAR BUMPER END RETAINER LH
  1. Engage the 2 claws and install the rear bumper end retainer LH.

  1. Install the screw.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }


13. INSTALL REAR BUMPER END RETAINER RH

HINT:
Use the same procedure as for the LH side.


14. INSTALL REAR BUMPER COVER
  1. Engage the 6 claws and the 2 clips and install the rear bumper cover.

  1. Connect the connector.

    HINT:
    If the vehicle is equipped with back sonar, connect the connector and install the floor wire.

  1. Connect the clamp and install the floor wire.

  1. B340061E02
    Install the 7 bolts and the 2 screws.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *3
    Screw

    Torque:
    for bolt A:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    for bolt B:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for screw:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. Remove the protective tape.

← INSTALLATION (Nov 2010 – Oct 2012)COMPONENTS (from Jul 2007) →