74-40 Short in Speaker Circuit
Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012
Versions by build date: Nov 2010 – Jul 2012 from Aug 2012
DESCRIPTION
| DTC No. |
DTC Detection Condition |
Trouble Area |
| 74-40 |
Short is detected in the speaker output circuit. |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- HINT:
- After the inspection is completed, clear the DTCs.
| 1. CONFIRM MODEL |
| Result |
Proceed to |
| for 10 speaker with sub-woofer |
A |
| for 8 speaker and 6 speaker |
B |
|
|
||||
| A | |
| 2. CHECK DTC |
Disconnect the K12 amplifier connector.
Clear the DTCs.
Check if DTC 74-40 is output.
- OK:
- DTC 74-40 is not output.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKER) |
Disconnect the K12 amplifier connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
K12-4 (FL+) - Body ground
Always
10 kΩ or higher
K12-11 (FL-) - Body ground
Always
10 kΩ or higher
K12-3 (FR+) - Body ground
Always
10 kΩ or higher
K12-8 (FR-) - Body ground
Always
10 kΩ or higher
K12-2 (FL+) - Body ground
Always
10 kΩ or higher
K12-7 (FL-) - Body ground
Always
10 kΩ or higher
K12-1 (FR+) - Body ground
Always
10 kΩ or higher
K12-6 (FR-) - Body ground
Always
10 kΩ or higher
K12-9 (RL+) - Body ground
Always
10 kΩ or higher
K12-10 (RL-) - Body ground
Always
10 kΩ or higher
K12-5 (RR+) - Body ground
Always
10 kΩ or higher
K12-12 (RR-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
Disconnect the H4 and G4 speaker connectors.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Always
Approximately 1.8 Ω
Text in Illustration *a
Component without harness connected
(Front No. 1 Speaker)
|
|
||||
| OK | |
| 5. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Disconnect the F3 and F4 speaker connectors.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 4
Always
Approximately 1.9 Ω
Text in Illustration *a
Component without harness connected
(Front No. 2 Speaker)
|
|
||||
| OK | |
| 6. INSPECT REAR SPEAKER ASSEMBLY |
Disconnect the L9 and L18 speaker connectors.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Always
Approximately 1.9 Ω
Text in Illustration *a
Component without harness connected
(Rear Speaker)
|
|
||||
| OK | |
| 7. INSPECT AMPLIFIER BOX SPEAKER ASSEMBLY |
Remove the amplifier box speaker assembly (Click here).

Remove the stereo component amplifier assembly from amplifier box speaker assembly (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
xC-5 (WFL+) - xC-12 (WFL-)
Always
Approximately 2 Ω
xC-4 (WFR+) - xC-10 (WFR-)
Always
Approximately 2 Ω
xC-5 (WFL+) - Body ground
Always
10 kΩ or higher
xC-12 (WFL-) - Body ground
Always
10 kΩ or higher
xC-4 (WFR+) - Body ground
Always
10 kΩ or higher
xC-10 (WFR-) - Body ground
Always
10 kΩ or higher
Text in Illustration *a
Component without harness connected
(Amplifier Box Speaker Assembly)
|
|
||||
| OK | ||
| ||
| 8. CHECK DTC |
Disconnect the E41 and E42 radio receiver connectors.
Clear the DTCs.
Check if DTC 74-40 is output.
- OK:
- DTC 74-40 is not output.
|
|
||||
| OK | |
| 9. CHECK DTC |
Reconnect the E42 radio receiver connector.
Clear the DTCs.
Check if DTC 74-40 is output.
- OK:
- DTC 74-40 is not output.
|
|
||||
| OK | |
| 10. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPEAKER) |
Disconnect the E41 radio receiver connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E41-2 (FL+) - Body ground
Always
10 kΩ or higher
E41-6 (FL-) - Body ground
Always
10 kΩ or higher
E41-1 (FR+) - Body ground
Always
10 kΩ or higher
E41-5 (FR-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 11. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
Disconnect the H4 and G4 speaker connectors.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Always
Approximately 4 Ω
Text in Illustration *a
Component without harness connected
(Front No. 1 Speaker)
|
|
||||
| OK | |
| 12. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Disconnect the F3 and F4 speaker connectors.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 4
Always
Approximately 8 Ω
Text in Illustration *a
Component without harness connected
(Front No. 2 Speaker)
|
|
||||
| OK | ||
| ||
| 13. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPEAKER) |
Disconnect the E42 radio receiver connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E42-2 (RL+) - Body ground
Always
10 kΩ or higher
E42-6 (RL-) - Body ground
Always
10 kΩ or higher
E42-1 (RR+) - Body ground
Always
10 kΩ or higher
E42-3 (RR-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 14. INSPECT ROOF SPEAKER ASSEMBLY |
Disconnect the R4 and R5 speaker connectors.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Always
Approximately 4 Ω
Text in Illustration *a
Component without harness connected
(Roof Speaker)
|
|
||||
| OK | |
| 15. INSPECT REAR SPEAKER ASSEMBLY |
Disconnect the L9 and L18 speaker connectors.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Always
Approximately 8 Ω
Text in Illustration *a
Component without harness connected
(Rear Speaker)
|
|
||||
| OK | |
| 16. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPEAKER CONDENSER) |
Disconnect the E42 receiver connector.
Disconnect the E27 condenser connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E42-2 (RL+) - E27-2 (LI+)
Always
Below 1 Ω
E42-6 (RL-) - E27-1 (LI-)
Always
Below 1 Ω
E42-1 (RR+) - E27-4 (RI+)
Always
Below 1 Ω
E42-3 (RR-) - E27-3 (RI-)
Always
Below 1 Ω
|
|
||||
| OK | |
| 17. CHECK HARNESS AND CONNECTOR (SPEAKER CONDENSER - ROOF SPEAKER) |
Disconnect the E27 condenser connector.
Disconnect the R4 and R5 speaker connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E27-6 (LO+) - R4-1
Always
Below 1 Ω
E27-5 (LO-) - R4-2
Always
Below 1 Ω
E27-8 (RO+) - R5-1
Always
Below 1 Ω
E27-7 (RO-) - R5-2
Always
Below 1 Ω
E27-6 (LO+) - Body ground
Always
10 kΩ or higher
E27-5 (LO-) - Body ground
Always
10 kΩ or higher
E27-8 (RO+) - Body ground
Always
10 kΩ or higher
E27-7 (RO-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 18. REPLACE SPEAKER CONDENSER |
Temporarily replace the condenser with a new or normally functioning one.
Check that the sound is normal.
- OK:
- Sound is normal.
|
|
||||
| OK | ||
| ||
