2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

74-40 Short in Speaker Circuit

Diagnostic trouble codes · Vehicles built from Aug 2012

Versions by build date: Nov 2010 – Jul 2012 from Aug 2012

DESCRIPTION

DTC No.
DTC Detection Condition
Trouble Area
74-40
Short is detected in the speaker output circuit.
  1. Harness or connector
  2. Speakers
  3. Stereo component amplifier assembly (for 10 speaker with sub-woofer)
  4. Radio receiver assembly (for 8 speaker and 6 speaker)

WIRING DIAGRAM

E221447E02
E219765E01

INSPECTION PROCEDURE

HINT:
After the inspection is completed, clear the DTCs.


1. CONFIRM MODEL
Result 
Result
Proceed to
for 10 speaker with sub-woofer
A
for 8 speaker and 6 speaker
B


B
Go to step 8
A


2. CHECK DTC
  1. Disconnect the K12 amplifier connector.

  1. Clear the DTCs.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKER)
  1. Disconnect the K12 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K12-4 (FL+) - Body ground
    Always
    10 kΩ or higher
    K12-11 (FL-) - Body ground
    Always
    10 kΩ or higher
    K12-3 (FR+) - Body ground
    Always
    10 kΩ or higher
    K12-8 (FR-) - Body ground
    Always
    10 kΩ or higher
    K12-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    K12-7 (FL-) - Body ground
    Always
    10 kΩ or higher
    K12-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    K12-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    K12-9 (RL+) - Body ground
    Always
    10 kΩ or higher
    K12-10 (RL-) - Body ground
    Always
    10 kΩ or higher
    K12-5 (RR+) - Body ground
    Always
    10 kΩ or higher
    K12-12 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

  1. E220304E01
    Disconnect the H4 and G4 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Approximately 1.8 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 1 Speaker)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


5. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

  1. E220305E01
    Disconnect the F3 and F4 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Always
    Approximately 1.9 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 2 Speaker)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


6. INSPECT REAR SPEAKER ASSEMBLY

  1. E197034E02
    Disconnect the L9 and L18 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Approximately 1.9 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Speaker)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


7. INSPECT AMPLIFIER BOX SPEAKER ASSEMBLY

  1. E221450E02
    Remove the amplifier box speaker assembly (Click here).

  1. Remove the stereo component amplifier assembly from amplifier box speaker assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    xC-5 (WFL+) - xC-12 (WFL-)
    Always
    Approximately 2 Ω
    xC-4 (WFR+) - xC-10 (WFR-)
    Always
    Approximately 2 Ω
    xC-5 (WFL+) - Body ground
    Always
    10 kΩ or higher
    xC-12 (WFL-) - Body ground
    Always
    10 kΩ or higher
    xC-4 (WFR+) - Body ground
    Always
    10 kΩ or higher
    xC-10 (WFR-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Amplifier Box Speaker Assembly)



NG
REPLACE AMPLIFIER BOX SPEAKER ASSEMBLY (Click here)
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

8. CHECK DTC
  1. Disconnect the E41 and E42 radio receiver connectors.

  1. Clear the DTCs.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
REPLACE RADIO RECEIVER ASSEMBLY
OK


9. CHECK DTC
  1. Reconnect the E42 radio receiver connector.

  1. Clear the DTCs.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
Go to step 13
OK


10. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPEAKER)
  1. Disconnect the E41 radio receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E41-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    E41-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    E41-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    E41-5 (FR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

  1. E220304E01
    Disconnect the H4 and G4 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Approximately 4 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 1 Speaker)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


12. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

  1. E220305E01
    Disconnect the F3 and F4 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Always
    Approximately 8 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 2 Speaker)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK

REPLACE RADIO RECEIVER ASSEMBLY

13. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPEAKER)
  1. Disconnect the E42 radio receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E42-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    E42-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    E42-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    E42-3 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14. INSPECT ROOF SPEAKER ASSEMBLY

  1. E220306E01
    Disconnect the R4 and R5 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Approximately 4 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Roof Speaker)



NG
REPLACE ROOF SPEAKER ASSEMBLY (Click here)
OK


15. INSPECT REAR SPEAKER ASSEMBLY

  1. E197034E02
    Disconnect the L9 and L18 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Approximately 8 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Speaker)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


16. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPEAKER CONDENSER)
  1. Disconnect the E42 receiver connector.

  1. Disconnect the E27 condenser connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E42-2 (RL+) - E27-2 (LI+)
    Always
    Below 1 Ω
    E42-6 (RL-) - E27-1 (LI-)
    Always
    Below 1 Ω
    E42-1 (RR+) - E27-4 (RI+)
    Always
    Below 1 Ω
    E42-3 (RR-) - E27-3 (RI-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


17. CHECK HARNESS AND CONNECTOR (SPEAKER CONDENSER - ROOF SPEAKER)
  1. Disconnect the E27 condenser connector.

  1. Disconnect the R4 and R5 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E27-6 (LO+) - R4-1
    Always
    Below 1 Ω
    E27-5 (LO-) - R4-2
    Always
    Below 1 Ω
    E27-8 (RO+) - R5-1
    Always
    Below 1 Ω
    E27-7 (RO-) - R5-2
    Always
    Below 1 Ω
    E27-6 (LO+) - Body ground
    Always
    10 kΩ or higher
    E27-5 (LO-) - Body ground
    Always
    10 kΩ or higher
    E27-8 (RO+) - Body ground
    Always
    10 kΩ or higher
    E27-7 (RO-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


18. REPLACE SPEAKER CONDENSER
  1. Temporarily replace the condenser with a new or normally functioning one.

  1. Check that the sound is normal.

    OK:
    Sound is normal.



NG
REPLACE RADIO RECEIVER ASSEMBLY
OK

END (SPEAKER CONDENSER IS DEFECTIVE)


← 74-40 Short in Speaker Circuit (Nov 2010 – Jul 2012)CB-10 System Microcomputer Malfunction (+ CB-11, CB-12) (Nov 2010 – Jul 2012) →