DISASSEMBLY
Removal / installation · Vehicles built from Jul 2007
- HINT:
- Use the same procedure for both the RH and LH sides.
- The procedure described below is for the RH side.
- Use the same procedure for both the RH and LH sides.
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT ARMREST BASE UPPER PANEL |
![]() ![]() |
Disengage the 3 claws and clip and remove the front armrest base upper panel.
Disconnect the connector.
| 3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side) |
Remove the 3 screws and the power window regulator master switch.

| 4. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side) |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the power window regulator switch.

| 5. REMOVE DOOR CONTROL SWITCH (for Front Passenger Side) |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the door control switch.

| 6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() ![]() |
for LH side:
Using a screwdriver with its tip wrapped in protective tape, open the 2 covers.
for RH side:

Using a screwdriver with its tip wrapped in protective tape, open the 2 covers.
Remove the 2 screws.

Disengage the 10 clips.

Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door trim board.

| 7. REMOVE FRONT NO.2 DOOR SERVICE HOLE COVER |
![]() ![]() |
Remove the 4 screws and front No. 2 door service hole cover.
| 8. REMOVE OUTER REAR VIEW MIRROR |
- HINT:
- Use the same procedure as for the LH side (Click here).
| 9. REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY |
- HINT:
- Use the same procedure as for the LH side (Click here).
| 10. REMOVE FRONT NO. 1 SPEAKER |
Disconnect the speaker connector.

Remove the 4 screws and the front No. 1 speaker.

| 11. REMOVE FRONT DOOR SERVICE HOLE COVER |
![]() ![]() |
Remove the front door service hole cover.
- NOTICE:
- Remove any tape remaining on the door side.
| 12. REMOVE FRONT DOOR INSIDE PANEL PLATE |
![]() ![]() |
Remove the 4 screws and the front door inside panel plate.
| 13. REMOVE FRONT DOOR CHECK ASSEMBLY |
![]() ![]() |
Remove the 2 nuts and bolt, then remove the front door check.
- NOTICE:
- Do not drop or damage the door check when removing the bolts.
- HINT:
- Remove the door check through the service hole.
| 14. REMOVE FRONT DOOR WEATHERSTRIP |
![]() ![]() |
Disengage the 24 clips and remove the front door weatherstrip.
- NOTICE:
- Remove any tape remaining on the door side.
| 15. REMOVE FRONT DOOR GLASS RUN |
![]() ![]() |
Remove the front door glass run.
| 16. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER |
![]() ![]() |
Remove the hole plug.
Remove the bolt and screw, then remove the front door frame sub-assembly front lower.

- NOTICE:
- Do not drop or damage the front door frame sub-assembly front lower when removing the bolt and screw.
| 17. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH |
![]() ![]() |
Remove the bolt and the 2 screws and remove front door lower frame bracket garnish.
| 18. REMOVE FRONT DOOR WINDOW FRAME REAR LOWER |
![]() ![]() |
Remove the bolt, then remove the front door window frame rear lower.
- NOTICE:
- Do not drop or damage the front door window frame rear lower when removing the bolt.
| 19. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY |
![]() ![]() |
Remove the hole plug.
Driver side:
Provisionally install the power window regulator master switch.
Passenger side:
Provisionally install the power window regulator switch.
Move the front door glass until the 2 bolts can be seen through the service holes.
Remove the 2 bolts.

Pull the door glass upward to remove it.
- NOTICE:
- Do not damage the glass.
Driver side:
Remove the power window regulator master switch.
Passenger side:
Remove the power window regulator switch.
| 20. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY |
![]() ![]() |
Disconnect the connector.
Remove the 6 bolts, then remove the front door window regulator.
- NOTICE:
- Do not drop or damage the front door window regulator.
- HINT:
- Remove the window regulator through the service hole.
| 21. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY |
Using "Torx" socket wrench T25, remove the 3 screws and the power window regulator motor.

| 22. REMOVE FRONT DOOR OUTSIDE HANDLE COVER |
![]() ![]() |
Remove the hole plug.
Using "Torx" socket wrench T30, loosen the screw and remove the cover with the door lock key cylinder installed.
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the front door outside handle cover.

| 23. REMOVE FRONT DOOR LOCK |
Using "Torx" socket wrench T30, loosen the 3 screws.

Move the front door lock downward, remove the outside handle frame link and remove the front door lock.
Disengage the 5 claws and open the cover.

Disconnect the front door lock remote control cable and the front door inside locking cable.

Remove the door lock wire harness seal.
| 24. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY |
![]() ![]() |
Remove the handle by sliding and pulling it in the direction indicated by the arrow mark in the illustration.
| 25. REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD |
![]() ![]() |
Disengage the 2 claws and remove the front door outside handle rear pad.
| 26. REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD |
![]() ![]() |
Disengage the 3 claws and remove the front door outside handle front pad.
| 27. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
![]() ![]() |
Using "Torx" socket wrench T30, loosen the screw.
Slide the front door outside handle frame to remove it.
- HINT:
- Remove the front door outside handle frame through the service hole.
| 28. REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY |
- HINT:
- Use the same procedure as for the LH side (Click here).
| 29. REMOVE CUSHION |
![]() ![]() |
Remove the 2 cushions.



















