INSTALLATION
Removal / installation · Vehicles built from Aug 2014
| 1. INSTALL FUEL TANK TO FILLER PIPE HOSE |
Install the fuel tank to filler pipe hose to the fuel tank assembly and tighten the hose clamp.

Text in Illustration *a
Fuel Tank Assembly Alignment Mark
*b
Fuel Tank to Filler Pipe Hose Alignment Mark
- HINT:
- Align the fuel tank assembly alignment mark and the fuel tank to filler pipe hose alignment mark in a straight line as shown in the illustration.
| 2. INSTALL FUEL TANK BREATHER TUBE SUB-ASSEMBLY |
Push the tube connector into the pipe until the connector makes a "click" sound and install the retainer.

Text in Illustration 

Push
- NOTICE:
- Check if there is any damage or foreign matter on the connected part of the pipe.
- After connecting, check if the pipe and the connector are securely connected by pulling them.
- Check if there is any damage or foreign matter on the connected part of the pipe.
| 3. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
Install the fuel suction with pump and gauge tube assembly (Click here).
| 4. INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY |
Connect the fuel tank main tube sub-assembly to the fuel suction tube with pump and gauge assembly.
Install the tube joint clip.


Text in Illustration *1
Tube Joint Clip
*2
Fuel Tube Joint
*3
Fuel Tank Main Tube Sub-assembly
*4
Fuel Suction Plate
*5
O-ring
-
-
*a
Correct
*b
Incorrect
*c
Rib
-
-
- NOTICE:
- Make sure there is no damage to or foreign matter on the connecting surfaces.
- Check that the fuel tube joint is correctly and fully inserted.
- Check that the main joint clip is above the rib of the main tube.
- After installing the tube joint clip, make sure the fuel tube joint will not come out.
- Do not damage any of the clips. If a clip is damaged, replace it.
- Make sure there is no damage to or foreign matter on the connecting surfaces.
Engage the 3 clamps and install the fuel tank main tube sub-assembly to the fuel tank assembly.
| 5. INSTALL FUEL TANK RETURN TUBE |
Connect the fuel tank return tube to the fuel suction tube with pump and gauge assembly.
Install the tube joint clip.


Text in Illustration *1
Tube Joint Clip
*2
Fuel Tube Joint
*3
Fuel Tank Main Tube Sub-assembly
*4
Fuel Suction Plate
*5
O-ring
-
-
*a
Correct
*b
Incorrect
*c
Rib
-
-
- NOTICE:
- Make sure there is no damage to or foreign matter on the connecting surfaces.
- Check that the fuel tube joint is correctly and fully inserted.
- Check that the main joint clip is above the rib of the main tube.
- After installing the tube joint clip, make sure the fuel tube joint will not come out.
- Do not damage any of the clips. If a clip is damaged, replace it.
- Make sure there is no damage to or foreign matter on the connecting surfaces.
Engage the 3 clamps and install the fuel tank return tube to the fuel tank assembly.
| 6. INSTALL FUEL TANK CUSHION |
Install the 4 new fuel tank cushions to the fuel tank assembly.
| 7. INSTALL NO. 3 FUEL TANK PROTECTOR |
Engage the 3 claws, and install the No. 3 fuel tank protector to the fuel tank assembly.
Install the 2 bolts to the No. 3 fuel tank protector.
- Torque:
- 5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
| 8. INSTALL FUEL TANK ASSEMBLY |
Set a transmission jack underneath the fuel tank assembly.
Install the fuel tank assembly to the vehicle.
Install the 2 fuel tank bands to the vehicle with the 2 bolts, 2 clips and 2 pins.
- Torque:
- 40 N*m{ 408 kgf*cm , 30 ft.*lbf }
| 9. CONNECT FUEL TANK VENT HOSE |
Align the axis of the fuel tank vent hose connector and the axis of the pipe, and push in the fuel tank vent hose connector until the retainer makes a click sound.

Text in Illustration 

Push
- NOTICE:
- Check that there are no scratches or foreign objects on the connecting part.
- Check that the fuel tank vent hose is inserted securely.
- Check that there are no scratches or foreign objects on the connecting part.
After connecting the fuel tank vent hose connector, pull on the fuel tank vent hose connector and the pipe to make sure they are firmly connected.
| 10. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY |
Align the axis of the fuel tank main tube sub-assembly connector and the axis of the pipe, and push in the fuel tank main tube sub-assembly connector until the retainer makes a click sound.

Text in Illustration *1
Retainer
*2
O-ring
*a
Lock
*b
Unlock
- NOTICE:
- Check that the fuel tank main tube sub-assembly is inserted securely.
After connecting the fuel tank main tube sub-assembly connector, pull on the fuel tank main tube sub-assembly connector and the pipe to make sure they are firmly connected.
| 11. CONNECT FUEL TANK RETURN TUBE |
Align the axis of the fuel tank return tube connector and the axis of the pipe, and push in the fuel tank return tube connector until the retainer makes a click sound.

Text in Illustration *1
Retainer
*2
O-ring
*a
Lock
*b
Unlock
- NOTICE:
- Check that the fuel tank return tube is inserted securely.
After connecting the fuel tank return tube connector, pull on the fuel tank return tube connector and the pipe to make sure they are firmly connected.
| 12. CONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY |
Align the axis of the fuel tank breather tube sub-assembly connector and the axis of the pipe, and push in the fuel cut-off tube connector until the retainer makes a click sound.

Text in Illustration 

Push
- NOTICE:
- Check that there are no scratches or foreign objects on the connecting part.
- Check that the fuel cut-off tube is inserted securely.
- Check that there are no scratches or foreign objects on the connecting part.
After connecting the fuel tank breather tube sub-assembly connector, pull on the fuel tank breather tube sub-assembly connector and the pipe to make sure they are firmly connected.
| 13. CONNECT FUEL TANK TO FILLER PIPE HOSE |
Connect the fuel tank to filler pipe hose to the fuel tank inlet pipe sub-assembly and tighten the hose clamp.
| 14. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Automatic Transmission) |
Install the No. 1 fuel tank protector sub-assembly to the fuel tank assembly with the 4 nuts.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
Install the No. 1 fuel tank protector sub-assembly bracket to the vehicle with the 2 nuts.
- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
| 15. INSTALL REAR FLOOR SERVICE HOLE COVER |
Connect the fuel suction tube with pump and gauge assembly connector.
Install the 3 screws to the rear floor service hole cover.
Install the center floor silencer pad LH to the vehicle.
Return the floor carpet.
| 16. INSTALL REAR DOOR SCUFF PLATE LH |
Engage the 6 claws and install the rear door scuff plate LH to the vehicle.
| 17. INSTALL FRONT DOOR SCUFF PLATE LH |
Engage the 14 claws and install the front door scuff plate LH to the vehicle.
| 18. INSTALL REAR SEAT CUSHION ASSEMBLY LH |
Install rear seat cushion assembly LH to the vehicle with the 2 bolts.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 19. INSPECT FOR FUEL LEAK |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
- NOTICE:
- Do not start the engine.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Speed / ON.
Check fuel pump operation.
Check for pressure in the fuel inlet tube from the fuel line. Check that the sound of fuel flowing in the fuel tank can be heard.
If there is no sound, check the integration relay, fuel pump, ECM and wiring connector.
