REMOVAL
Removal / installation · Vehicles built from Aug 2014
| 1. DISCHARGE FUEL SYSTEM PRESSURE |
Discharge the fuel system pressure (Click here).
| 2. REMOVE FRONT DOOR SCUFF PLATE LH |
Disengage the 14 claws and remove the front door scuff plate LH from the vehicle.

| 3. REMOVE REAR DOOR SCUFF PLATE LH |
Disengage the 6 claws and remove the rear door scuff plate LH from the vehicle.

| 4. REMOVE REAR SEAT CUSHION ASSEMBLY LH |
Remove the 2 bolts and rear seat cushion assembly LH from the vehicle.

| 5. REMOVE REAR FLOOR SERVICE HOLE COVER |
Turn back the floor carpet.
Remove the center floor silencer pad LH from the vehicle.

Remove the 3 screws from the rear floor service hole cover from the vehicle.

Disconnect the fuel suction tube with pump and gauge assembly connector.

| 6. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY |
Remove the 2 nuts and No. 1 fuel tank protector sub-assembly bracket from the vehicle.

Remove the 4 nuts and No. 1 fuel tank protector sub-assembly from the fuel tank assembly.

| 7. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY |
- NOTICE:
- Before disconnecting the fuel tank main tube sub-assembly connector, check for dirt or other foreign matter on the fuel tank main tube sub-assembly connector and the pipe, and clean them if necessary.
Pinch the retainer to disengage the lock claws and pull out the fuel tank main tube sub-assembly from the pipe.

Text in Illustration *1
Retainer
*2
O-ring
*a
Lock
*b
Unlock
- NOTICE:
- If the fuel tank main tube sub-assembly connector and pipe are stuck together, push in and pull out the fuel tank main tube sub-assembly connector while squeezing the pipe to release the connection, and then disconnect the fuel tank main tube sub-assembly connector.
- Clean away any dirt or foreign matter from the fuel tank main tube sub-assembly connector before performing the operation.
- The fuel tank main tube sub-assembly connector and pipe are sealed by O-ring, so be careful to prevent damage to and foreign matter sticking to the contact surfaces.
- Do not use any tools.
- After disconnecting the fuel tank main tube sub-assembly connector, check that there is no foreign matter on the seal surface of the pipe.
- After disconnecting the fuel tank main tube sub-assembly, protect the contact surfaces by covering them with a plastic bag.
- Do not bend or twist the tubes.
- If the fuel tank main tube sub-assembly connector and pipe are stuck together, push in and pull out the fuel tank main tube sub-assembly connector while squeezing the pipe to release the connection, and then disconnect the fuel tank main tube sub-assembly connector.
| 8. DRAIN FUEL |
| 9. DISCONNECT FUEL TANK TO FILLER PIPE HOSE |
Loosen the hose clamp and disconnect the fuel tank to filler pipe hose from the fuel tank inlet pipe sub-assembly.

| 10. DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY |
Turn the retainer to disengage the lock claws and pull out the fuel tank breather tube sub-assembly from the pipe.

Text in Illustration *1
Retainer
*2
O-ring


Turn
- NOTICE:
- If the fuel tank breather tube sub-assembly connector and pipe are stuck together, push in and pull out the fuel tank breather tube sub-assembly connector while squeezing the pipe to release the connection, and then disconnect the fuel tank breather tube sub-assembly connector.
- Clean away any dirt or foreign matter from the fuel tank breather tube sub-assembly connector before performing the operation.
- The fuel tank breather tube sub-assembly connector and pipe are sealed by O-ring, so be careful to prevent damage to and foreign matter sticking to the contact surfaces.
- Do not use any tools.
- After disconnecting the fuel tank breather tube sub-assembly connector, check that there is no foreign matter on the seal surface of the pipe.
- After disconnecting the fuel tank breather tube sub-assembly, protect the contact surfaces by covering them with a plastic bag.
- Do not bend or twist the tubes.
- If the fuel tank breather tube sub-assembly connector and pipe are stuck together, push in and pull out the fuel tank breather tube sub-assembly connector while squeezing the pipe to release the connection, and then disconnect the fuel tank breather tube sub-assembly connector.
| 11. DISCONNECT FUEL TANK RETURN TUBE |
- NOTICE:
- Before disconnecting the fuel tank return tube connector, check for dirt or other foreign matter on the fuel tank return tube connector and the pipe, and clean them if necessary.
Pinch the retainer to disengage the lock claws and pull out the fuel tank return tube from the pipe.

Text in Illustration *1
Retainer
*2
O-ring
*a
Lock
*b
Unlock
- NOTICE:
- If the fuel tank return tube connector and pipe are stuck together, push in and pull out the fuel tank return tube connector while squeezing the pipe to release the connection, and then disconnect the fuel tank return tube connector.
- Clean away any dirt or foreign matter from the fuel tank return tube connector before performing the operation.
- The fuel tank return tube connector and pipe are sealed by O-ring, so be careful to prevent damage to and foreign matter sticking to the contact surfaces.
- Do not use any tools.
- After disconnecting the fuel tank return tube connector, check that there is no foreign matter on the seal surface of the pipe.
- After disconnecting the fuel tank return tube, protect the contact surfaces by covering them with a plastic bag.
- Do not bend or twist the tubes.
- If the fuel tank return tube connector and pipe are stuck together, push in and pull out the fuel tank return tube connector while squeezing the pipe to release the connection, and then disconnect the fuel tank return tube connector.
| 12. DISCONNECT FUEL TANK VENT HOSE |
Disconnect the fuel tank vent hose from the fuel tank.

Text in Illustration 

Pinch


Push
Push the fuel tank vent hose connector firmly.
Pinch portion A, as shown in the illustration.
Pull out the fuel tank vent hose connector.
| 13. REMOVE FUEL TANK ASSEMBLY |
Set a transmission jack underneath the fuel tank assembly.

Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands from the vehicle.
Remove the fuel tank assembly from the vehicle.
| 14. REMOVE NO. 3 FUEL TANK PROTECTOR |
Remove the 2 bolts.


Disengage the 3 claws and remove the No. 3 fuel tank protector from the fuel tank assembly.
| 15. REMOVE FUEL TANK CUSHION |
Remove the 4 fuel tank cushions from the fuel tank assembly.

| 16. REMOVE FUEL TANK RETURN TUBE |
Remove the tube joint clip, and pull out the fuel tank return tube from the fuel suction tube with pump and gauge assembly.

Text in Illustration *1
O-ring


Pull
- NOTICE:
- If the fuel tank return tube connector and pipe are stuck together, push in and pull out the fuel tank return tube connector while squeezing the pipe to release the connection, and then disconnect the fuel tank return tube connector.
- Clean away any dirt or foreign matter from the fuel tank return tube connector before performing the operation.
- The fuel tank return tube connector and pipe are sealed by O-ring, so be careful to prevent damage to and foreign matter sticking to the contact surfaces.
- Do not use any tools.
- After disconnecting the fuel tank return tube connector, check that there is no foreign matter on the seal surface of the pipe.
- After disconnecting the fuel tank return tube, protect the contact surfaces by covering them with a plastic bag.
- Do not bend or twist the tubes.
- If the fuel tank return tube connector and pipe are stuck together, push in and pull out the fuel tank return tube connector while squeezing the pipe to release the connection, and then disconnect the fuel tank return tube connector.
Disengage the 3 clamps and remove the fuel tank return tube from the fuel tank assembly.

| 17. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY |
Remove the tube joint clip, and pull out the fuel tank main tube sub-assembly from the fuel suction tube with pump and gauge assembly.

Text in Illustration *1
O-ring


Pull
- NOTICE:
- If the fuel tank main tube sub-assembly connector and pipe are stuck together, push in and pull out the fuel tank main tube sub-assembly connector while squeezing the pipe to release the connection, and then disconnect the fuel tank main tube sub-assembly connector.
- Clean away any dirt or foreign matter from the fuel tank main tube sub-assembly connector before performing the operation.
- The fuel tank main tube sub-assembly connector and pipe are sealed by O-ring, so be careful to prevent damage to and foreign matter sticking to the contact surfaces.
- Do not use any tools.
- After disconnecting the fuel tank main tube sub-assembly connector, check that there is no foreign matter on the seal surface of the pipe.
- After disconnecting the fuel tank main tube sub-assembly, protect the contact surfaces by covering them with a plastic bag.
- Do not bend or twist the tubes.
- If the fuel tank main tube sub-assembly connector and pipe are stuck together, push in and pull out the fuel tank main tube sub-assembly connector while squeezing the pipe to release the connection, and then disconnect the fuel tank main tube sub-assembly connector.
Disengage the 3 clamps and remove the fuel tank main tube sub-assembly from the fuel tank assembly.

| 18. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
Remove the fuel suction with pump and gauge tube assembly (Click here).
| 19. REMOVE FUEL TANK BREATHER TUBE SUB-ASSEMBLY |
Pinch the retainer to disengage the lock claws and pull out the fuel tank breather tube sub-assembly.

Text in Illustration *1
Retainer
*2
O-ring


Turn


Pull
- NOTICE:
- Check that there is no dirt or mud around the quick connector before performing this work, because the quick connector has an O-ring which seals the pipe and connector. Clean the connector if necessary.
- Do not use any tools in this work.
- Do not bend or twist the nylon tube.
- To protect the tube, cover it with a vinyl bag after disconnecting it.
- When the connector and the pipe are stuck, turn the fuel tank breather tube carefully to disconnect them.
- Check that there is no dirt or mud around the quick connector before performing this work, because the quick connector has an O-ring which seals the pipe and connector. Clean the connector if necessary.
| 20. REMOVE FUEL TANK TO FILLER PIPE HOSE |
Loosen the hose clamp and remove the fuel tank to filler pipe hose from the fuel tank assembly.

