Remove the nut and the fuel tank protector bracket.
Remove the 4 nuts and the fuel tank protector.
4.
DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Pinch the retainer to disengage the lock claws and pull out the fuel tank main tube.
Text in Illustration
*1
Retainer
*2
O-Ring
*a
Lock
*b
Unlock
NOTICE:
Check that there is no dirt or mud around the quick connector before performing this work because the quick connector has an O-ring which seals the pipe and the connector. Clean the connector if necessary.
Do not use any tools in this work.
Do not bend or twist the nylon tube.
To protect the tube, cover it with a vinyl bag after disconnecting it.
When the connector and the pipe are stuck, turn the retainer carefully to disconnect them.
5.
DRAIN FUEL
Operate the fuel pump and drain the fuel from the fuel tank through the fuel tank main tube (Click here).
6.
REMOVE FRONT DOOR SCUFF PLATE LH
Disengage the 14 claws and remove the front door scuff plate.
7.
REMOVE REAR DOOR SCUFF PLATE LH
Disengage the 6 claws and remove the rear door scuff plate.
8.
REMOVE REAR SEAT CUSHION ASSEMBLY LH
Remove the 2 bolts, then remove the rear seat cushion LH.
9.
REMOVE REAR FLOOR SERVICE HOLE COVER
Pull back the floor carpet.
Remove the center floor silencer pad LH.
Remove the 3 screws from the center floor.
Disconnect the connector.
10.
DISCONNECT FUEL TANK TO FILLER PIPE HOSE
Loosen the clamp bolt and disconnect the fuel tank to filler pipe hose.
11.
DISCONNECT FUEL TANK RETURN TUBE
Pinch the retainer to disengage the lock claws and pull out the fuel tank return tube.
Text in Illustration
*1
Retainer
*2
O-Ring
*a
Lock
*b
Unlock
NOTICE:
Check that there is no dirt or mud around the quick connector before performing this work because the quick connector has an O-ring which seals the pipe and the connector. Clean the connector if necessary.
Do not use any tools in this work.
Do not bend or twist the nylon tube.
To protect the tube, cover it with a vinyl bag after disconnecting it.
When the connector and the pipe are stuck, turn the retainer carefully to disconnect them.
12.
DISCONNECT FUEL CUT-OFF TUBE
Turn the retainer to disengage the lock claws and pull out the fuel cut off tube.
Text in Illustration
*1
Retainer
*2
O-Ring
*3
Fuel Pipe
*4
Nylon Tube
Turn
Pull
NOTICE:
Check that there is no dirt or mud around the quick connector before performing this work because the quick connector has an O-ring which seals the pipe and the connector. Clean the connector if necessary.
Do not use any tools in this work.
Do not bend or twist the nylon tube.
To protect the tube, cover it with a vinyl bag after disconnecting it.
When the connector and the pipe are stuck, turn the retainer carefully to free and then disconnect the fuel tank tube.
13.
DISCONNECT FUEL TANK BREATHER TUBE
Disconnect the fuel tank breather tube from the fuel tank.
Text in Illustration
Pinch
Push
Push the connector firmly.
Pinch portion A, as shown in the illustration.
Pull out the connector.
14.
REMOVE FUEL TANK ASSEMBLY
Hold the fuel tank using a mission jack.
Remove the 2 fuel tank bands.
Remove the 2 bolts.
Remove the 2 clips and 2 pins, then remove the 2 fuel tank bands.
15.
REMOVE NO. 3 FUEL TANK PROTECTOR
Remove the 2 bolts and disengage the 3 claws, then remove the No. 3 fuel tank protector.
16.
REMOVE FUEL TANK CUSHION
Remove the 4 fuel tank cushions from the fuel tank.
17.
REMOVE FUEL TANK MAIN TUBE AND FUEL TANK RETURN TUBE
Remove the 2 joint clips, and pull out the 2 fuel tank tubes.
Text in Illustration
*1
O-Ring
Pull
NOTICE:
Check that there is no dirt or mud around the quick connector before performing this work because the quick connector has an O-ring which seals the pipe and the connector. Clean the connector if necessary.
Do not use any tools in this work.
Do not bend or twist the nylon tube by force.
After disconnecting, cover the fuel tube joint with a vinyl bag.
When the fuel tube joint and fuel suction plate are stuck, turn the fuel tank main tube carefully to free and then disconnect it. Likewise, disconnect the fuel tank return tube.
18.
REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
NOTICE:
Protect the connector and tube joint with masking tape or equivalent to prevent any foreign matter from sticking to them. Clean any dirt and foreign matter from the fuel suction tube assembly before removing.