2011-2016 FJ Cruiser · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL INLET OIL COOLER HOSE (for Automatic Transmission)

A129889

2. INSTALL NO. 1 RADIATOR HOSE

A129887

3. INSTALL NO. 2 RADIATOR HOSE

A129888

4. INSTALL RADIATOR ASSEMBLY

  1. Install the radiator with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


    A129886

  1. A129943
    Connect the 2 oil cooler hoses (w/ automatic transmission).

  1. A129883
    Install the 2 radiator hoses.


5. INSTALL RADIATOR GRILLE

  1. B134729
    Engage the 5 clips and install the radiator grille.

  1. Tighten the 2 screws.

    Torque:
    3.0 N*m{ 30 kgf*cm , 27 in.*lbf }

  1. Install the 2 clips.


6. INSTALL FAN SHROUD
  1. Temporarily install the fan shroud together with the fluid coupling assembly with fan.

  1. Temporarily install the fluid coupling assembly with fan with the 4 nuts.

  1. Install the fan and generator V belt.
    (Click here)

  1. A129882
    Install the fan pulley with the 4 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. A129885E01
    Install the bolt to the reserve tank.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the fan shroud with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the bolt to the reserve tank.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the 2 oil cooler hoses with the 2 clamps (w/ automatic transmission).

  1. A129881
    Connect the hose to the radiator reserve tank.


7. INSTALL RADIATOR SUPPORT SEAL UPPER

  1. A129880E01
    Engage the 7 clips, then install the radiator support seal.


8. ADD ENGINE COOLANT
  1. Pour coolant into the radiator until it overflows.

    Capacity:
    Transmission
    Capacity
    Manual Transmission
    9.4 liters (9.9 Us qts, 8.3 Imp. qts)
    Automatic Transmission
    9.8 liters (10.4 Us qts, 8.6 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    3. New TOYOTA vehicles are filled with TOYOTA SLLC (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)). When replacing the coolant, TOYOTA SLLC is recommended.

  1. Check the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.

  1. Install the radiator cap securely.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Condition
      Fan Speed
      Any setting except OFF
      Temperature
      Toward WARM
      Air Conditioning Switch
      OFF

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
      3. If there is not enough coolant, the engine may burn out or overheat.

  1. Squeeze the inlet and outlet radiator hoses several times by hand while warming up the engine to bleed the air.

    CAUTION:
    When pressing the radiator hoses:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, repeat the operation until the coolant level remains at the full level.

  1. Check the coolant level inside the radiator reservoir tank again. If it is below the full level, add coolant.


9. CHECK ENGINE COOLANT LEAK
  1. Remove the radiator cap.

    CAUTION:
    To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. A072543E02
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Pump it to 118 kPa (1.2 kgf/cm2, 17.1 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage. If there are no signs of external coolant leakage, check the heater core, cylinder block and head.

  1. Reinstall the radiator cap.


10. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Install the No. 1 engine under cover with the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


11. INSTALL V-BANK COVER

  1. A126475
    Install the V-bank cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

← REASSEMBLY (Jul 2007 – Jul 2009)INSTALLATION (Aug 2009 – Oct 2010) →