2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Reverse Signal Circuit

Circuit diagnosis · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

This circuit sends a signal of the back-up light switch or park/neutral position switch to the clearance warning ECU.

WIRING DIAGRAM

E160751E01

INSPECTION PROCEDURE


1. CHECK TRANSMISSION TYPE
  1. Check the transmission type.

    Result 
    Result
    Proceed to
    Automatic Transmission
    A
    Manual Transmission
    B



B
Go to step 4
A


2. INSPECT PARK / NEUTRAL POSITION SWITCH

  1. E160755E01
    Disconnect the B35 park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below..

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B35-2 (RB) - B35-1 (RL)
    Shift lever in R
    Below 1 Ω
    B35-2 (RB) - B35-1 (RL)
    Shift lever not in R
    10 kΩ or higher

  1. Reconnect the park/neutral position switch connector.



NG
REPLACE PARK / NEUTRAL POSITION SWITCH (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (PARK / NEUTRAL POSITION SWITCH - CLEARANCE WARNING ECU)

  1. E160753E01
    Disconnect the B35 park/neutral position switch connector.

  1. Disconnect the E31 or E76 clearance warning ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B35-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o Rear Fog Light 
    Tester Connection
    Condition
    Specified Condition
    B35-1 (RL) - E31-8 (RL)
    Always
    Below 1 Ω
    w/ Rear Fog Light 
    Tester Connection
    Condition
    Specified Condition
    B35-1 (RL) - E76-13 (RL)
    Always
    Below 1 Ω

  1. Reconnect the park/neutral position switch connector.

  1. Reconnect the clearance warning ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

4. INSPECT BACK-UP LIGHT SWITCH

  1. E160756E01
    Remove the back-up light switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pushed
    Below 1 Ω
    Not pushed
    10 kΩ or higher

  1. Reinstall the back-up light switch.



NG
REPLACE BACK-UP LIGHT SWITCH
OK


5. CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH - CLEARANCE WARNING ECU)

  1. E160754E01
    Disconnect the B42 back-up light switch connector.

  1. Disconnect the E31 clearance warning ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B42-2 - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B42-1 - E31-8 (RL)
    Always
    Below 1 Ω

  1. Reconnect the back-up light switch connector.

  1. Reconnect the clearance warning ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Speed Signal Circuit (from Nov 2012)Reverse Signal Circuit (from Nov 2010) →