2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Reverse Signal Circuit

Circuit diagnosis · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

This circuit sends a signal of the back-up light switch or park/neutral position switch to the clearance warning ECU.

WIRING DIAGRAM

B268488E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK TRANSMISSION TYPE
  1. Check the transmission type.

    Result 
    Result
    Proceed to
    Automatic Transmission
    A
    Manual Transmission
    B



B
Go to step 4
A


2. INSPECT PARK/NEUTRAL POSITION SWITCH
  1. Inspect the park/neutral position switch (Click here).



NG
REPLACE PARK/NEUTRAL POSITION SWITCH (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - CLEARANCE WARNING ECU AND IGNITION SWITCH)
  1. Disconnect the B35 park/neutral position switch connector.

  1. Disconnect the E76 clearance warning ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B35-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B35-1 (RL) - E76-13 (RL)
    Always
    Below 1 Ω

  1. Reconnect the park/neutral position switch connector.

  1. Reconnect the clearance warning ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

4. INSPECT BACK-UP LIGHT SWITCH

  1. B268889E01
    Remove the back-up light switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pushed
    Below 1 Ω
    Not pushed
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Back-up Light Switch)

  1. Reinstall the back-up light switch.



NG
REPLACE BACK-UP LIGHT SWITCH
OK


5. CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH - CLEARANCE WARNING ECU AND IGNITION SWITCH)
  1. Disconnect the B42 back-up light switch connector.

  1. Disconnect the E76 clearance warning ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B42-2 - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B42-1 - E76-13 (RL)
    Always
    Below 1 Ω

  1. Reconnect the back-up light switch connector.

  1. Reconnect the clearance warning ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Reverse Signal Circuit (Jul 2007 – Oct 2010)Back Sonar Sensor Circuit (Jul 2007 – Oct 2010) →