2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Rear Wiper Motor Circuit

Circuit diagnosis · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 from Aug 2011

DESCRIPTION

The back door ECU controls the rear wiper motor.

WIRING DIAGRAM

E152590E01

INSPECTION PROCEDURE


1. CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs.

  1. Check whether DTC B1214, B1215 or B1287 recurs 10 seconds or more after the ignition switch is turned on.

    OK:
    No DTC is output.



NG
GO TO MULTIPLEX COMMUNICATION SYSTEM (Click here)
OK


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR WIPER)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Body Electrical / Back Door / Active Test / Rear Wiper.

  1. Check the rear wiper while operating the back door ECU using the tester.

    Back-Door:
    Tester Operation
    Specified Condition
    Rear Wiper OFF
    Rear wiper off
    Rear Wiper ON
    Rear wiper operates



NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

3. CHECK HARNESS AND CONNECTOR (BACK DOOR ECU - BATTERY, IGNITION SWITCH, BODY GROUND)

  1. E152593E01
    Disconnect the S2 back door ECU connector.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S2-4 (BDR) - Body ground
    Always
    11 to 14 V
    S2-5 (BECU) - Body ground
    Always
    11 to 14 V
    S2-6 (SIG) - Body ground
    Ignition Switch
    OFF → ON
    Below 1 V → 11 to 14 V

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S2-3 (GND) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the back door ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT REAR WIPER MOTOR ASSEMBLY
E034081E29
  1. Remove the rear wiper motor assembly.

  1. Connect the battery's positive (+) lead to terminal 5 (L) and the negative (-) lead to terminal 4 (E).

  1. Check that the rear wiper motor operates.

    OK:
    Rear wiper motor operates.

  1. Reinstall the rear wiper motor assembly.



NG
REPLACE REAR WIPER MOTOR ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - BACK DOOR ECU)

  1. B062909E01
    Disconnect the S3 rear wiper motor assembly connector.

  1. Disconnect the S5 back door ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    S5-1 (WIP-) - S3-4 (E)
    Always
    Below 1 Ω
    S5-2 (WIP+) - S3-5 (L)
    Always
    Below 1 Ω
    S5-3 (W) - S3-3 (W)
    Always
    Below 1 Ω
    S5-12 (P) - S3-1 (P)
    Always
    Below 1 Ω
    S5-18 (SGND) - S3-2 (E)
    Always
    Below 1 Ω
    S5-2 (WIP+) - Body ground
    Always
    10 kΩ or higher
    S5-3 (W) - Body ground
    Always
    10 kΩ or higher
    S5-12 (P) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the the rear wiper motor assembly connector.

  1. Reconnect the back door ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK DOOR ECU (Click here)


← DATA LIST / ACTIVE TEST (from Jul 2007)Rear Wiper Motor Circuit (Aug 2009 – Oct 2010) →