2011-2016 FJ Cruiser · Service Manual COMMUNICATION SYSTEM

Skid Control ECU Communication Stop Mode

Circuit diagnosis · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

DESCRIPTION

Detection Item
Symptom
Trouble Area
Skid Control ECU Communication Stop Mode
  1. "ABS/VSC/TRAC" not displayed on "Bus Check" screen of intelligent tester
  2. Applies to "Skid Control ECU Communication Stop Mode" in "DTC combination table"
  1. Power source circuit of master cylinder solenoid (skid control ECU)
  2. Master cylinder solenoid (skid control ECU) branch wire or connector
  3. Master cylinder solenoid (skid control ECU)

WIRING DIAGRAM

E214873E04
E214873E05

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
  4. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN IN CAN BUS WIRE (MASTER CYLINDER SOLENOID (SKID CONTROL ECU) BRANCH WIRE)
  1. Turn the ignition switch off.

  1. B255884E02
    Disconnect the A4 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-11 (CANH) - A4-25 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid (Skid Control ECU))



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK


3. CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID (SKID CONTROL ECU) - BATTERY AND BODY GROUND)
  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. B255884E03
    Disconnect the A4 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-32 (GND2) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-46 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid (Skid Control ECU))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)


← Skid Control ECU Communication Stop Mode (Jul 2007 – Oct 2010)Steering Angle Sensor Communication Stop Mode (Jul 2007 – Oct 2010) →