INSTALLATION
Removal / installation · Vehicles built Jul 2007 – Jul 2009
Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010
| 1. INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER |
![]() ![]() |
Install a new bearing spacer.
- HINT:
- Install the spacer in the correct direction.
| 2. INSTALL FRONT DIFFERENTIAL OIL STORAGE RING |
Using a brass bar and hammer, tap in a new oil storage ring.
- NOTICE:
- Be careful not to damage the oil storage ring.
| 3. INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() ![]() |
Using SST and a hammer, install the roller bearing (outer).
- SST
- 09316-60011
(09316-00011, 09316-00021)
Install the roller bearing (inner).
| 4. INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER |
| 5. INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL |
![]() ![]() |
Apply MP grease to the lip of a new oil seal.
Using SST and a hammer, tap in the oil seal.
- SST
- 09554-22010
- Oil seal depth:
- 3.9 to 4.8 mm (0.154 to 0.188 in.)
| 6. INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
![]() ![]() |
Using SST, instal the companion flange.
- SST
- 09950-30012
(09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)
- NOTICE:
- Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
Using SST to hold the companion flange, install the nut.
- SST
- 09330-00021
(09330-00030)
- Torque:
- 370 N*m{ 3,770 kgf*cm , 273 ft.*lbf } or less
| 7. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD |
![]() ![]() |
Using a torque wrench, measure the preload.
- Preload (at starting):
Item
Specified Condition
New bearing
0.98 to 1.57 N*m (10 to 16 kgf*cm, 8.7 to 13.9 in.*lbf)
Used bearing
0.49 to 0.78 N*m (5 to 8 kgf*cm, 4.3 to 6.9 in.*lbf)
| 8. STAKE FRONT DRIVE PINION COMPANION FLANGE NUT |
![]() ![]() |
Using a chisel and hammer, stake the nut.
| 9. INSTALL FRONT PROPELLER SHAFT ASSEMBLY |
Align the matchmarks on the yoke and differential flange.

Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.
- Torque:
- 88 N*m{ 899 kgf*cm , 65 ft.*lbf }
Align the matchmarks on the yoke and transfer flange.

Install the propeller shaft assembly with the 4 nuts and 4 washers.
- Torque:
- 88 N*m{ 899 kgf*cm , 65 ft.*lbf }
| 10. ADD DIFFERENTIAL OIL |
![]() ![]() |
Stop the vehicle on a level surface.
Remove the differential filler plug and gasket.
Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the differential filler plug hole.
- NOTICE:
- After changing the oil seal, drive the vehicle and then check the oil level again.
- After changing the oil seal, drive the vehicle and then check the oil level again.
- Too much or too little oil will lead to differential problems.
- Too much or too little oil will lead to differential problems.
- HINT:
- If necessary, fill the differential carrier assembly with hypoid gear oil.
- Front Differential:
Item
Temperature
Oil grade
Viscosity
Capacity
w/ A.D.D.
-
Hypoid gear oil API GL-4 or GL-5
SAE 75W-90
1.45 to 1.55 liters
(1.53 to 1.63 US qts, 1.27 to 1.36 Imp. qts.)
w/o A.D.D.
Above -18 °C (-0.4 °F)
SAE 90
1.35 to 1.45 liters
(1.42 to 1.53 US qts, 1.18 to 1.27 Imp. qts.)
Below -18 °C (-0.4 °F)
SAE 85W-90
- Rear Differential:
Item
Temperature
Oil grade
Viscosity
Capacity
w/o Differential lock
Above -18 °C (-0.4 °F)
Hypoid gear oil API GL-5
SAE 90
2.95 to 3.05 liters
(3.12 to 3.22 US qts, 2.60 to 2.68 Imp. qts.)
Below -18 °C (-0.4 °F)
SAE 85W-90
w/ Differential lock
Above -18 °C (-0.4 °F)
SAE 90
2.85 to 2.95 liters
(3.01 to 3.12 US qts, 2.51 to 2.60 Imp. qts.)
Below -18 °C (-0.4 °F)
SAE 85W-90
Check for oil leakage when the oil level is low.
Install the differential filler plug with a new gasket.
- Torque:
- Front differential:
- 39 N*m{ 400 kgf*cm , 29 ft.*lbf }
- Rear differential:
- 49 N*m{ 500 kgf*cm , 36 ft.*lbf }
| 11. CHECK FOR DIFFERENTIAL OIL LEAKAGE |
| 12. INSTALL REAR ENGINE UNDER COVER ASSEMBLY |
Install the rear engine under cover with the 4 bolts.
- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
| 13. INSTALL NO. 1 ENGINE UNDER COVER |
Install the No. 1 engine under cover with the 4 bolts.
- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }







