2011-2016 FJ Cruiser · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2010

Versions by build date: Aug 2009 – Oct 2010 from Nov 2010


1. INSTALL REAR CRANKSHAFT OIL SEAL

A076329E02
  1. Apply MP grease to the lip of a new oil seal.

  1. Using SST and a hammer, tap in the oil seal until its surface is flush with the rear oil seal retainer edge.

    SST
    09223-78010  

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap the oil seal at an angle.


2. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. Temporarily install the flywheel with the 8 new bolts.

  1. Install and tighten the 8 mounting bolts uniformly in several steps.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Mark the top of the bolts with paint.

  1. Tighten the 8 bolts 90° in the same sequence.

  1. Check that the paint marks are now at a 90° angle to the top.


3. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

C135774
  1. Insert SST into the clutch disc assembly, then insert them into the flywheel sub-assembly.

    SST
    09301-00220  

    NOTICE:
    Insert the clutch disc assembly in the correct orientation.


4. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

C135776E02
  1. Align the matchmarks on the clutch cover assembly and flywheel sub-assembly.

    Text in Illustration 
    *a
    Temporarily
    *b
    Matchmark

  1. Following the procedures shown in the illustration, tighten the 6 bolts, in the order starting with the bolt located near the knock pin on the top.

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

    HINT:
    1. Following the order in the illustration, uniformly tighten the bolts.
    2. Move SST up and down, right and left lightly, after checking that the disc is in the center, and tighten the bolts.


5. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)

C135777
  1. Using a dial indicator with roller instrument, check the diaphragm spring tip alignment.

    Maximum non-alignment:
    0.5 mm (0.020 in.)

    If the alignment is not as specified, adjust the diaphragm spring tip alignment using SST.
    SST
    09333-00013  


6. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A227952E01
    Install the front drive plate spacer, drive plate and ring gear and rear drive plate spacer onto the crankshaft.
    Text in Illustration 
    *1
    Front Drive Plate Spacer
    *2
    Drive Plate and Ring Gear
    *3
    Rear Drive Plate Spacer
    V100135
    Transmission Side

    HINT:
    As the front drive plate spacer, drive plate and ring gear and rear drive plate spacer are not reversible, be sure to install it in the direction shown in the illustration.

  1. A057108
    Apply adhesive to the 2 or 3 end threads of the bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

  1. A224777E01
    Uniformly install and tighten the 8 bolts in several steps in the sequence shown in the illustration.

    Torque:
    83 N*m{ 846 kgf*cm , 61 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 1 hour after installing.


7. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
  1. Install the manual transmission (Click here).


8. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
  1. Install the automatic transmission (Click here).

← INSTALLATION (Aug 2009 – Oct 2010)COMPONENTS (Jul 2007 – Jul 2009) →