2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1637/82 Lost Communication with Passenger Side Rear Airbag Sensor

Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012

Also covers:

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012

DESCRIPTION

The front passenger side - side airbag sensor and front passenger side - rear airbag sensor consist of parts including the diagnostic circuit and the lateral deceleration sensor.
When center airbag sensor assembly receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1637/82 and B1638/82 are set when a malfunction is detected in the front passenger side - side airbag sensor or front passenger side - rear airbag sensor circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1637/82
B1638/82
  1. Center airbag sensor assembly detects open circuit signal in front passenger side - side airbag sensor circuit or front passenger side - rear airbag sensor circuit for 2 seconds.
  2. Front passenger side - side airbag sensor malfunction
  3. Front passenger side - rear airbag sensor malfunction
  4. Center airbag sensor assembly malfunction
  1. Front passenger side floor wire
  2. Front passenger side - side airbag sensor
  3. Front passenger side - rear airbag sensor
  4. Center airbag sensor assembly

WIRING DIAGRAM

C148422E44
C148422E47

INSPECTION PROCEDURE


1. CHECK CONNECTORS (FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR - FRONT PASSENGER SIDE - REAR AIRBAG SENSOR)
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the front passenger side floor wire connectors from the front passenger side - side airbag sensor and the front passenger side - rear airbag sensor.

  1. Check the front passenger side floor wire connectors and terminals (on the front passenger side - side airbag sensor and the front passenger side - rear airbag sensor sides) and check that the connectors are properly connected.

    Result 
    Result
    Proceed to
    No problem.
    A
    Connectors or terminals incorrect.
    B
    Connectors connected improperly.
    C



B
REPLACE FRONT PASSENGER SIDE FLOOR WIRE

C
CONNECT CONNECTORS PROPERLY
A


2. CHECK FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR
  1. Connect the connector to the center airbag sensor assembly.

  1. C135745E02
    Interchange the front passenger side - side airbag sensor with the driver side - side airbag sensor and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Text in Illustration 
    *a
    Driver Side - Side Airbag Sensor
    *b
    Center Airbag Sensor Assembly
    *c
    DLC3
    *d
    DTC 81
    *e
    DTC 82
    Result 
    Result
    Proceed to
    DTC B1637/82 or B1638/82 is output.
    A
    DTC B1632/81 or B1633/81 is output.
    B
    DTCs B1632/81, B1633/81, B1637/82 and B1638/82 are not output.
    C

    HINT:
    DTCs other than DTC B1632/81, B1633/81, B1637/82 and B1638/82 may be output at this time, but they are not related to this check.



B
REPLACE FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


3. CHECK FRONT PASSENGER SIDE FLOOR WIRE (FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR - FRONT PASSENGER SIDE - REAR AIRBAG SENSOR)

  1. H100841E14
    Turn the ignition switch off.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front Passenger Side - Rear Airbag Sensor
    *b
    Front Passenger Side - Side Airbag Sensor
    *c
    Front Passenger Side Floor Wire
    *d
    Front view of wire harness connector
    (to Front Passenger Side - Rear Airbag Sensor)
    *e
    Front view of wire harness connector
    (to Front Passenger Side - Side Airbag Sensor)
    *f
    Connector C
    *g
    Connector B
    *h
    Service Wire

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check for open in the circuit.

    1. Using a service wire, connect 1 and 2 of connector C.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      K2-1 (BCR+) - K2-2 (BCR-)
      Always
      Below 1 Ω
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      L4-1 (BCL+) - L4-2 (BCL-)
      Always
      Below 1 Ω

  1. H100842E17
    Check for short in the circuit.
    1. Disconnect the service wire from connector C.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      K2-1 (BCR+) - K2-2 (BCR-)
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      L4-1 (BCL+) - L4-2 (BCL-)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      K2-1 (BCR+) - Body ground
      Always
      1 MΩ or higher
      K2-2 (BCR-) - Body ground
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      L4-1 (BCL+) - Body ground
      Always
      1 MΩ or higher
      L4-2 (BCL-) - Body ground
      Always
      1 MΩ or higher

  1. Check for short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      K2-1 (BCR+) - Body ground
      Ignition switch ON
      Below 1 V
      K2-2 (BCR-) - Body ground
      Ignition switch ON
      Below 1 V
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      L4-1 (BCL+) - Body ground
      Ignition switch ON
      Below 1 V
      L4-2 (BCL-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Front Passenger Side - Rear Airbag Sensor
      *b
      Front Passenger Side - Side Airbag Sensor
      *c
      Front Passenger Side Floor Wire
      *d
      Front view of wire harness connector
      (to Front Passenger Side - Side Airbag Sensor)
      *e
      Connector B



NG
REPLACE FRONT PASSENGER SIDE FLOOR WIRE
OK


4. CHECK FRONT PASSENGER SIDE - REAR AIRBAG SENSOR
  1. Connect the connector to the front passenger side - side airbag sensor.

  1. C135743E03
    Interchange the front passenger side - rear airbag sensor with the driver side - rear airbag sensor and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Text in Illustration 
    *a
    Driver Side - Rear Airbag Sensor
    *b
    Front Passenger Side - Side Airbag Sensor
    *c
    DLC3
    *d
    DTC 81
    *e
    DTC 82
    Result 
    Result
    Proceed to
    DTCs B1632/81, B1633/81, B1637/82 and B1638/82 are not output.
    A
    DTC B1637/82 or B1638/82 is output.
    B
    DTC B1632/81 or B1633/81 is output.
    C

    HINT:
    DTCs other than DTC B1632/81, B1633/81, B1637/82 and B1638/82 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE FRONT PASSENGER SIDE - REAR AIRBAG SENSOR (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← B1637/82 Lost Communication with Passenger Side Rear Airbag Sensor (+ B1638/82) (Jul 2007 – Oct 2010)B1638/82 Rear Airbag Sensor Assembly LH Initialization Incomplete (from Aug 2012) →