2011-2016 FJ Cruiser · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Nov 2012 – Jul 2014

Versions by build date: Aug 2009 – Oct 2010 Nov 2010 – Oct 2012 Nov 2012 – Jul 2014 from Aug 2014


1. DISCONNECT HEATER WATER HOSE ASSEMBLY

A225928
  1. Disconnect the 2 hoses and remove the heater water hose assembly.


2. REMOVE IGNITION COIL ASSEMBLY

A224724
  1. Remove the 6 bolts and 6 ignition coils.


3. REMOVE REAR CYLINDER HEAD COVER

  1. A224695
    Remove the 3 bolts and cover.


4. REMOVE FUEL PIPE SUB-ASSEMBLY

A224750
  1. Disconnect the 2 fuel pipes (Click here).

  1. Remove the 2 bolts and No. 1 fuel pipe and No. 2 fuel pipe.


5. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A223037
    Disconnect the 6 fuel injector connectors.

  1. Remove the 4 bolts and fuel delivery pipe together with the 6 fuel injectors.

    NOTICE:
    Be careful not to drop the injectors when removing the fuel delivery pipe.


6. REMOVE FUEL INJECTOR ASSEMBLY

  1. A223038E02
    Pull the 6 fuel injectors from the fuel delivery pipe.
    Text in Illustration 
    *1
    Fuel Delivery Pipe
    *2
    Fuel Injector

  1. Remove the O-ring and injector vibration insulator from each fuel injector.


7. REMOVE INTAKE MANIFOLD

  1. A221466
    Remove the 4 nuts, 6 bolts and intake manifold.

  1. Remove the 2 gaskets.


8. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY (w/ Oil Cooler)

A225999
  1. Disconnect the 4 hoses.

  1. Remove the 3 bolts and water by-pass pipe.


9. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

A158544
  1. Remove the bolt and No. 1 idler pulley.


10. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

A223006
  1. for Cover Separate Type:
    Remove the 2 bolts, 2 idler pulley cover plates, 2 No. 2 idler pulleys, and 2 No. 2 idler pulley cover plates.

  1. for Cover Integrated Type:
    Remove the 2 bolts and 2 No. 2 idler pulleys.


11. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

A222180
  1. Remove the 5 bolts and V-ribbed belt tensioner.


12. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

A222114
  1. Remove the dipstick.

  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.


13. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

  1. A221156
    Remove the 3 bolts and front No. 1 engine mounting bracket LH.


14. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

  1. A221155
    Remove the 4 bolts and front No. 1 engine mounting bracket RH.


15. REMOVE FLYWHEEL RING GEAR (for Manual Transmission)

CAUTION:
Wear protective gloves. Hot areas on the flywheel ring gear may injure your hands.

HINT:
If the flywheel ring gear is deformed or the gears are damaged, replace it.

  1. A177669E01
    Using a torch, heat the ring gear evenly to approximately 200°C (392°F).

  1. Temporarily install 6 bolts (8 mm (0.315 in.) x 1.25 pitch) with a length of 70 mm (2.76 in.) or more to the flywheel.

  1. Uniformly tighten the 6 bolts in the order shown in the illustration.

  1. Remove the ring gear from the flywheel.

← REMOVAL (Nov 2010 – Oct 2012)REMOVAL (from Aug 2014) →