2011-2016 FJ Cruiser · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2009 – Oct 2010 Nov 2010 – Oct 2012 Nov 2012 – Jul 2014 from Aug 2014


1. DISCONNECT HEATER WATER HOSE ASSEMBLY

A225928
  1. Disconnect the 2 hoses and remove the heater water hose assembly.


2. REMOVE NO. 1 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

  1. A225367
    Remove the 3 nuts and No. 1 emission control valve set from the cylinder head cover sub-assembly.


3. REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

  1. A225368
    Remove the 3 nuts and No. 2 emission control valve set from the cylinder head cover sub-assembly LH.


4. REMOVE IGNITION COIL ASSEMBLY

A224724
  1. Remove the 6 bolts and 6 ignition coils.


5. REMOVE REAR CYLINDER HEAD COVER

  1. A224695
    Remove the 3 bolts and cover.


6. REMOVE FUEL PIPE SUB-ASSEMBLY

A224750
  1. Disconnect the 2 fuel pipes (Click here).

  1. Remove the 2 bolts and No. 1 fuel pipe and No. 2 fuel pipe.


7. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A223037
    Disconnect the 6 fuel injector connectors.

  1. Remove the 4 bolts and fuel delivery pipe together with the 6 fuel injectors.

    NOTICE:
    Be careful not to drop the injectors when removing the fuel delivery pipe.


8. REMOVE FUEL INJECTOR ASSEMBLY

  1. A223038E02
    Pull the 6 fuel injectors from the fuel delivery pipe.
    Text in Illustration 
    *1
    Fuel Delivery Pipe
    *2
    Fuel Injector

  1. Remove the O-ring and injector vibration insulator from each fuel injector.


9. REMOVE INTAKE MANIFOLD

  1. A244715
    Remove the bolt to separate the wire harness clamp bracket from the intake manifold.

  1. A221466E02
    Remove the 4 nuts, 6 bolts and intake manifold from the cylinder head sub-assembly.
    Text in Illustration 
    *1
    Nut

  1. Remove the No. 1 intake manifold to head gasket and No. 2 intake manifold to head gasket from the cylinder head sub-assembly.


10. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY (w/ Oil Cooler)

A225999
  1. Disconnect the 4 hoses.

  1. Remove the 3 bolts and water by-pass pipe.


11. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

A158544
  1. Remove the bolt and No. 1 idler pulley.


12. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

A223006
  1. for Cover Separate Type:
    Remove the 2 bolts, 2 idler pulley cover plates, 2 No. 2 idler pulleys, and 2 No. 2 idler pulley cover plates.

  1. for Cover Integrated Type:
    Remove the 2 bolts and 2 No. 2 idler pulleys.


13. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

A222180
  1. Remove the 5 bolts and V-ribbed belt tensioner.


14. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

A222114
  1. Remove the dipstick.

  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.


15. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

  1. A221156
    Remove the 3 bolts and front No. 1 engine mounting bracket LH.


16. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

  1. A221155
    Remove the 4 bolts and front No. 1 engine mounting bracket RH.


17. REMOVE FLYWHEEL RING GEAR (for Manual Transmission)

CAUTION:
Wear protective gloves. Hot areas on the flywheel ring gear may injure your hands.

HINT:
If the flywheel ring gear is deformed or the gears are damaged, replace it.

  1. A177669E01
    Using a torch, heat the ring gear evenly to approximately 200°C (392°F).

  1. Temporarily install 6 bolts (8 mm (0.315 in.) x 1.25 pitch) with a length of 70 mm (2.76 in.) or more to the flywheel.

  1. Uniformly tighten the 6 bolts in the order shown in the illustration.

  1. Remove the ring gear from the flywheel.

← REMOVAL (Nov 2012 – Jul 2014)DISASSEMBLY (Jul 2007 – Jul 2009) →