2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Speaker Circuit

Circuit diagnosis · Vehicles built Nov 2010 – Jul 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

DESCRIPTION

  1. The stereo component amplifier sends sound signals to the speakers (for 10 speaker with sub-woofer).
  2. The radio receiver sends sound signals to the speakers (for 8 speaker and 6 speaker).

WIRING DIAGRAM

E221447E02
E219765E01

INSPECTION PROCEDURE


1. CONFIRM MODEL
Result 
Result
Proceed to
for 10 speaker with sub-woofer
A
for 8 speaker and 6 speaker
B


B
Go to step 13
A


2. CHECK SPEAKER
  1. Check the malfunctioning speakers.

    Result 
    Result
    Proceed to
    Front No. 1 speaker
    A
    Front No. 2 speaker
    B
    Rear speaker (for 8 speaker)
    C
    Amplifier box speaker assembly
    D



B
Go to step 6

C
Go to step 9

D
Go to step 12
A


3. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

  1. E220304E01
    Disconnect the H4 and G4 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Approximately 1.8 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 1 Speaker)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (AMPLIFIER BOX SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER)
  1. Disconnect the H4 and G4 speaker connectors.

  1. Disconnect the K12 box speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    K12-4 (FL+) - H4-1
    Always
    Below 1 Ω
    K12-11 (FL-) - H4-2
    Always
    Below 1 Ω
    K12-4 (FL+) - Body ground
    Always
    10 kΩ or higher
    K12-11 (FL-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    K12-3 (FR+) - G4-1
    Always
    Below 1 Ω
    K12-8 (FR-) - G4-2
    Always
    Below 1 Ω
    K12-3 (FR+) - Body ground
    Always
    10 kΩ or higher
    K12-8 (FR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT AMPLIFIER BOX SPEAKER ASSEMBLY

  1. E221448E02
    Remove the amplifier box speaker assembly (Click here).

  1. Remove the stereo component amplifier assembly from the amplifier box speaker assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K12-4 (FL+) - xC-2 (FL+)
    Always
    Below 1 Ω
    K12-11 (FL-) - xC-1 (FL-)
    Always
    Below 1 Ω
    K12-3 (FR+) - xC-9 (FR+)
    Always
    Below 1 Ω
    K12-8 (FR-) - xC-3 (FR-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Amplifier Box Speaker Assembly)



NG
REPLACE AMPLIFIER BOX SPEAKER ASSEMBLY (Click here)
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

6. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

  1. E220305E01
    Disconnect the F3 and F4 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Always
    Approximately 1.9 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 2 Speaker)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (AMPLIFIER BOX SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER)
  1. Disconnect the F3 and F4 speaker connectors.

  1. Disconnect the K12 box speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    K12-2 (FL+) - F4-4
    Always
    Below 1 Ω
    K12-7 (FL-) - F4-3
    Always
    Below 1 Ω
    K12-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    K12-7 (FL-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    K12-1 (FR+) - F3-4
    Always
    Below 1 Ω
    K12-6 (FR-) - F3-3
    Always
    Below 1 Ω
    K12-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    K12-6 (FR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. INSPECT AMPLIFIER BOX SPEAKER ASSEMBLY

  1. E221449E03
    Remove the amplifier box speaker assembly (Click here).

  1. Remove the stereo component amplifier assembly from the amplifier box speaker assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K12-2 (FL+) - xB-8 (FL+)
    Always
    Below 1 Ω
    K12-7 (FL-) - xB-7 (FL-)
    Always
    Below 1 Ω
    K12-1 (FR+) - xB-2 (FR+)
    Always
    Below 1 Ω
    K12-6 (FR-) - xB-6 (FR-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Amplifier Box Speaker Assembly)



NG
REPLACE AMPLIFIER BOX SPEAKER ASSEMBLY (Click here)
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

9. INSPECT REAR SPEAKER ASSEMBLY

  1. E197034E02
    Disconnect the L9 and L18 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Approximately 1.9 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Speaker)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


10. CHECK HARNESS AND CONNECTOR (AMPLIFIER BOX SPEAKER ASSEMBLY - REAR SPEAKER)
  1. Disconnect the L9 and L18 speaker connectors.

  1. Disconnect the K12 box speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    K12-9 (RL+) - L9-1
    Always
    Below 1 Ω
    K12-10 (RL-) - L9-2
    Always
    Below 1 Ω
    K12-9 (RL+) - Body ground
    Always
    10 kΩ or higher
    K12-9 (RL+) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    K12-5 (RR+) - L18-1
    Always
    Below 1 Ω
    K12-12 (RR-) - L18-2
    Always
    Below 1 Ω
    K12-5 (RR+) - Body ground
    Always
    10 kΩ or higher
    K12-12 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. INSPECT AMPLIFIER BOX SPEAKER ASSEMBLY

  1. E221449E04
    Remove the amplifier box speaker assembly (Click here).

  1. Remove the stereo component amplifier assembly from the amplifier box speaker assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K12-9 (RL+) - xB-3 (RL-)
    Always
    Below 1 Ω
    K12-10 (RL-) - xB-9 (RL-)
    Always
    Below 1 Ω
    K12-5 (RR+) - xB-10 (RR+)
    Always
    Below 1 Ω
    K12-12 (RR-) - xB-4 (RR-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Amplifier Box Speaker Assembly)



NG
REPLACE AMPLIFIER BOX SPEAKER ASSEMBLY (Click here)
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

12. INSPECT AMPLIFIER BOX SPEAKER ASSEMBLY

  1. E221450E02
    Remove the amplifier box speaker assembly (Click here).

  1. Remove the stereo component amplifier assembly from amplifier box speaker assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    xC-5 (WFL+) - xC-12 (WFL-)
    Always
    Approximately 2 Ω
    xC-4 (WFR+) - xC-10 (WFR-)
    Always
    Approximately 2 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Amplifier Box Speaker Assembly)



NG
REPLACE AMPLIFIER BOX SPEAKER ASSEMBLY (Click here)
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

13. CHECK SPEAKER
  1. Check the malfunctioning speakers.

    Result 
    Result
    Proceed to
    Front No. 1 speaker
    A
    Front No. 2 speaker
    B
    Rear speaker
    C
    Roof speaker
    D



B
Go to step 16

C
Go to step 18

D
Go to step 20
A


14. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

  1. E220304E01
    Disconnect the H4 and G4 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Approximately 4 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 1 Speaker)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


15. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - FRONT NO. 1 SPEAKER)
  1. Disconnect the H4 and G4 speaker connectors.

  1. Disconnect the E41 receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    E41-2 (FL+) - H4-1
    Always
    Below 1 Ω
    E41-6 (FL-) - H4-2
    Always
    Below 1 Ω
    E41-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    E41-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    E41-1 (FR+) - G4-1
    Always
    Below 1 Ω
    E41-5 (FR-) - G4-2
    Always
    Below 1 Ω
    E41-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    E41-5 (FR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)

16. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

  1. E220305E01
    Disconnect the F3 and F4 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Always
    Approximately 8 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 2 Speaker)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


17. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - FRONT NO. 2 SPEAKER)
  1. Disconnect the F3 and F4 speaker connectors.

  1. Disconnect the E41 receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    E41-2 (FL+) - F4-4
    Always
    Below 1 Ω
    E41-6 (FL-) - F4-3
    Always
    Below 1 Ω
    E41-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    E41-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    E41-1 (FR+) - F3-4
    Always
    Below 1 Ω
    E41-5 (FR-) - F3-3
    Always
    Below 1 Ω
    E41-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    E41-5 (FR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)

18. INSPECT REAR SPEAKER ASSEMBLY

  1. E197034E02
    Disconnect the L9 and L18 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Approximately 8 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Speaker)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


19. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - REAR SPEAKER)
  1. Disconnect the L9 and L18 speaker connectors.

  1. Disconnect the K12 box speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    E42-2 (RL+) - L9-1
    Always
    Below 1 Ω
    E42-6 (RL-) - L9-2
    Always
    Below 1 Ω
    E42-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    E42-6 (RL+) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    E42-1 (RR+) - L18-1
    Always
    Below 1 Ω
    E42-3 (RR-) - L18-2
    Always
    Below 1 Ω
    E42-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    E42-3 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)

20. INSPECT ROOF SPEAKER ASSEMBLY

  1. E220306E01
    Disconnect the R4 and R5 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Approximately 4 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Roof Speaker)



NG
REPLACE ROOF SPEAKER ASSEMBLY (Click here)
OK


21. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPEAKER CONDENSER)
  1. Disconnect the E42 receiver connector.

  1. Disconnect the E27 condenser connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    E42-2 (RL+) - E27-2 (LI+)
    Always
    Below 1 Ω
    E42-6 (RL-) - E27-1 (LI-)
    Always
    Below 1 Ω
    E42-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    E42-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    E42-1 (RR+) - E27-4 (RI+)
    Always
    Below 1 Ω
    E42-3 (RR-) - E27-3 (RI-)
    Always
    Below 1 Ω
    E42-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    E42-3 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


22. CHECK HARNESS AND CONNECTOR (SPEAKER CONDENSER - ROOF SPEAKER)
  1. Disconnect the E27 condenser connector.

  1. Disconnect the R4 and R5 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    E27-6 (LO+) - R4-1
    Always
    Below 1 Ω
    E27-5 (LO-) - R4-2
    Always
    Below 1 Ω
    E27-6 (LO+) - Body ground
    Always
    10 kΩ or higher
    E27-5 (LO-) - Body ground
    Always
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    E27-8 (RO+) - R5-1
    Always
    Below 1 Ω
    E27-7 (RO-) - R5-2
    Always
    Below 1 Ω
    E27-8 (RO+) - Body ground
    Always
    10 kΩ or higher
    E27-7 (RO-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


23. REPLACE SPEAKER CONDENSER
  1. Temporarily replace the condenser with a new or normally functioning one.

  1. Check that the sound is normal.

    OK:
    Sound is normal.



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK

END (SPEAKER CONDENSER IS DEFECTIVE)


← Speaker Circuit (Jul 2007 – Oct 2010)Speaker Circuit (from Aug 2012) →