2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Back Sonar Sensor Circuit

Circuit diagnosis · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

CAUTION / NOTICE / HINT

HINT:
This procedure applies only for vehicles with rear fog lights.


DESCRIPTION

This circuit shows the sensor power supply, sensor GND, and sensor signal wires between the clearance warning ECU and No. 1 ultrasonic sensors. The No. 1 ultrasonic sensors are digital sensors.

WIRING DIAGRAM

E160767E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - NO. 1 ULTRASONIC SENSOR RH)

  1. E160765E01
    Disconnect the E76 clearance warning ECU connector.

  1. Disconnect the N6 No. 1 ultrasonic sensor RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E76-24 (BOR) - N6-1 (BI)
    Always
    Below 1 Ω
    E76-6 (SOR) - N6-3 (SI)
    E76-22 (E2) - N6-5 (EI)
    E76-24 (BOR) - Body ground
    Always
    10 kΩ or higher
    E76-6 (SOR) - Body ground
    E76-22 (E2) - Body ground

  1. Reconnect the clearance warning ECU connector.

  1. Reconnect the No. 1 ultrasonic sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. REPLACE NO. 1 ULTRASONIC SENSOR RH
  1. Replace the No. 1 ultrasonic sensor RH with a normally functioning sensor (Click here).

    HINT:
    All the ultrasonic sensors are the same. Switch the right and left sensors to confirm if the sensors function normally.


NEXT


3. CHECK TOYOTA PARKING ASSIST-SENSOR SYSTEM
  1. Check the operation of the Toyota parking assist-sensor system (Click here).

    Result 
    Result
    Proceed to
    Toyota parking assist-sensor system malfunction
    A
    Toyota parking assist-sensor system normal operation
    B



B
END (NO. 1 ULTRASONIC SENSOR RH MALFUNCTION)
A


4. CHECK HARNESS AND CONNECTOR (ULTRASONIC SENSOR RH - ULTRASONIC SENSOR LH)

  1. E160766E01
    Disconnect the N6 No. 1 ultrasonic sensor RH connector.

  1. Disconnect the N9 No. 1 ultrasonic sensor LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N6-2 (BO) - N9-1 (BI)
    Always
    Below 1 Ω
    N6-4 (SO) - N9-3 (SI)
    N6-6 (EO) - N9-5 (EI)
    N9-2 (BO) - Body ground
    Always
    10 kΩ or higher
    N9-4 (SO) - Body ground
    N9-6 (EO) - Body ground

  1. Reconnect the No. 1 ultrasonic sensor connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE NO. 1 ULTRASONIC SENSOR LH
  1. Replace the No. 1 ultrasonic sensor LH with a normally functioning sensor (Click here).

    HINT:
    All the ultrasonic sensors are the same. Switch the right and left sensors to confirm if the sensors function normally.


NEXT


6. CHECK TOYOTA PARKING ASSIST-SENSOR SYSTEM
  1. Check the operation of the toyota parking assist-sensor system (Click here).

    Result 
    Result
    Proceed to
    Toyota parking assist-sensor system malfunction
    A
    Toyota parking assist-sensor system normal operation
    B



B
END (NO. 1 ULTRASONIC SENSOR LH MALFUNCTION)
A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Reverse Signal Circuit (from Nov 2010)Back Sonar Sensor Circuit (from Nov 2010) →