2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Back Sonar Sensor Circuit

Circuit diagnosis · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Oct 2010 from Nov 2010

CAUTION / NOTICE / HINT


DESCRIPTION

This circuit shows the sensor power supply, sensor GND, and sensor signal wires between the clearance warning ECU and No. 1 ultrasonic sensors. The No. 1 ultrasonic sensors are digital sensors.

WIRING DIAGRAM

E160767E02

INSPECTION PROCEDURE


1. SYSTEM CHECK
  1. Check the vehicle specifications.

    Result 
    Result
    Proceed to
    w/ Rear Fog Light
    A
    w/o Rear Fog Light
    B



B
Go to step 8
A


2. CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - NO. 1 ULTRASONIC SENSOR LH)
  1. Disconnect the E76 clearance warning ECU connector.

  1. Disconnect the N9 No. 1 ultrasonic sensor LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E76-24 (BOR) - N9-1 (BI)
    Always
    Below 1 Ω
    E76-6 (SOR) - N9-3 (SI)
    E76-22 (E2) - N9-5 (EI)
    E76-24 (BOR) - Body ground
    Always
    10 kΩ or higher
    E76-6 (SOR) - Body ground
    E76-22 (E2) - Body ground

  1. Reconnect the clearance warning ECU connector.

  1. Reconnect the No. 1 ultrasonic sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. REPLACE NO. 1 ULTRASONIC SENSOR LH
  1. Replace the No. 1 ultrasonic sensor LH with a normally functioning sensor (Click here).

    HINT:
    All the ultrasonic sensors are the same. Switch the right and left sensors to confirm if the sensors function normally.


NEXT


4. CHECK TOYOTA PARKING ASSIST-SENSOR SYSTEM
  1. Check the operation of the Toyota parking assist-sensor system (Click here).

    Result 
    Result
    Proceed to
    Toyota parking assist-sensor system malfunction
    A
    Toyota parking assist-sensor system normal operation
    B



B
END (NO. 1 ULTRASONIC SENSOR LH MALFUNCTION)
A


5. CHECK HARNESS AND CONNECTOR (ULTRASONIC SENSOR LH - ULTRASONIC SENSOR RH)
  1. Disconnect the N9 No. 1 ultrasonic sensor LH connector.

  1. Disconnect the N8 No. 1 ultrasonic sensor RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N9-2 (BO) - N8-1 (BI)
    Always
    Below 1 Ω
    N9-4 (SO) - N8-3 (SI)
    N9-6 (EO) - N8-5 (EI)
    N9-2 (BO) - Body ground
    Always
    10 kΩ or higher
    N9-4 (SO) - Body ground
    N9-6 (EO) - Body ground

  1. Reconnect the No. 1 ultrasonic sensor connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE NO. 1 ULTRASONIC SENSOR RH
  1. Replace the No. 1 ultrasonic sensor RH with a normally functioning sensor (Click here).

    HINT:
    All the ultrasonic sensors are the same. Switch the right and left sensors to confirm if the sensors function normally.


NEXT


7. CHECK TOYOTA PARKING ASSIST-SENSOR SYSTEM
  1. Check the operation of the Toyota parking assist-sensor system (Click here).

    Result 
    Result
    Proceed to
    Toyota parking assist-sensor system malfunction
    A
    Toyota parking assist-sensor system normal operation
    B



B
END (NO. 1 ULTRASONIC SENSOR RH MALFUNCTION)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

8. CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - NO. 1 ULTRASONIC SENSOR LH)
  1. Disconnect the E76 clearance warning ECU connector.

  1. Disconnect the d2 No. 1 ultrasonic sensor LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E76-24 (BOR) - d2-1 (BI)
    Always
    Below 1 Ω
    E76-6 (SOR) - d2-3 (SI)
    E76-22 (E2) - d2-5 (EI)
    E76-24 (BOR) - Body ground
    Always
    10 kΩ or higher
    E76-6 (SOR) - Body ground
    E76-22 (E2) - Body ground

  1. Reconnect the clearance warning ECU connector.

  1. Reconnect the No. 1 ultrasonic sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. REPLACE NO. 1 ULTRASONIC SENSOR LH
  1. Replace the No. 1 ultrasonic sensor LH with a normally functioning sensor (Click here).

    HINT:
    All the ultrasonic sensors are the same. Switch the right and left sensors to confirm if the sensors function normally.


NEXT


10. CHECK TOYOTA PARKING ASSIST-SENSOR SYSTEM
  1. Check the operation of the Toyota parking assist-sensor system (Click here).

    Result 
    Result
    Proceed to
    Toyota parking assist-sensor system malfunction
    A
    Toyota parking assist-sensor system normal operation
    B



B
END (NO. 1 ULTRASONIC SENSOR LH MALFUNCTION)
A


11. CHECK HARNESS AND CONNECTOR (ULTRASONIC SENSOR LH - ULTRASONIC SENSOR RH)
  1. Disconnect the d2 No. 1 ultrasonic sensor LH connector.

  1. Disconnect the d1 No. 1 ultrasonic sensor RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    d2-2 (BO) - d1-1 (BI)
    Always
    Below 1 Ω
    d2-4 (SO) - d1-3 (SI)
    d2-6 (EO) - d1-5 (EI)
    d2-2 (BO) - Body ground
    Always
    10 kΩ or higher
    d2-4 (SO) - Body ground
    d2-6 (EO) - Body ground

  1. Reconnect the No. 1 ultrasonic sensor connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12. REPLACE NO. 1 ULTRASONIC SENSOR RH
  1. Replace the No. 1 ultrasonic sensor RH with a normally functioning sensor (Click here).

    HINT:
    All the ultrasonic sensors are the same. Switch the right and left sensors to confirm if the sensors function normally.


NEXT


13. CHECK TOYOTA PARKING ASSIST-SENSOR SYSTEM
  1. Check the operation of the Toyota parking assist-sensor system (Click here).

    Result 
    Result
    Proceed to
    Toyota parking assist-sensor system malfunction
    A
    Toyota parking assist-sensor system normal operation
    B



B
END (NO. 1 ULTRASONIC SENSOR RH MALFUNCTION)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Back Sonar Sensor Circuit (Jul 2007 – Oct 2010)Back Sonar Sensor LH Circuit (Jul 2007 – Oct 2010) →