2011-2016 FJ Cruiser · Service Manual BRAKE

C1439 Steering Angle Sensor Initialization Incomplete

Diagnostic trouble codes · Vehicles built from Aug 2012

Also covers:

Versions by build date: Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012

DESCRIPTION

The skid control ECU acquires steering angle sensor zero point every time the ignition switch is turned to ON and the vehicle is driven at 40 km/h (25 mph) or more for approximately 10 seconds. The ECU also stores the previous zero point.
The steering angle sensor zero point malfunction warning will be cancelled by turning the ignition switch to off.
DTC Code
DTC Detection Condition
Trouble Area
C1439
After the steering angle sensor 0 calibration is cleared due to, for example, fluctuations in the power source, the steering angle 0 calibration cannot be obtained for 60 seconds of continuous driving
  1. Steering angle sensor
  2. Yaw rate and deceleration sensor
  3. Brake actuator assembly (Skid control ECU)
C1445
Steering angle sensor 0 calibration cannot be obtained when the vehicle is driven without a record of steering angle sensor 0 calibration at a speed of 36 km/h (22 mph) or more for 30 seconds or more without the brake pedal being depressed
  1. Steering angle sensor
  2. Yaw rate and deceleration sensor
  3. Brake actuator assembly (Skid control ECU)

INSPECTION PROCEDURE

NOTICE:
  1. Before proceeding with the inspection, explain to the customer that the output DTC is related to temporary loss of the steering angle zero calibration, such as when the power voltage drops when the battery is removed, and confirm that this condition occurred.
  2. When replacing the master cylinder solenoid, perform calibration (Click here).
  3. When replacing the brake actuator assembly, perform zero point calibration (Click here).

HINT:
  1. When DTC U0073, U0123, U0124 and/or U0126 is output together with DTC C1439 and/or C1445, inspect and repair the trouble areas indicated by DTC U0073, U0123, U0124 and/or U0126 first (Click here).
  2. When the speed sensor or the yaw rate and deceleration sensor has trouble, DTCs for the steering angle sensor may be stored even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate and deceleration sensor are output together with other DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and deceleration sensor first, and then inspect and repair the steering angle sensor.


1. CHECK DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON again and check that no CAN communication system DTC is output.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) and turn the steering wheel to the right and left, and then check that no speed sensor and yaw rate and deceleration sensor DTCs are output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    C1439 and/or C1445
    A
    Relating to CAN communication system
    B
    Relating to speed sensor or yaw rate and deceleration sensor
    C
    DTC is not output
    D

    HINT:
    1. If there is a malfunction in the speed sensor or the yaw rate and deceleration sensor, an abnormal value may be output although the steering angle sensor is normal.
    2. If the speed sensor and the yaw rate and deceleration sensor DTCs are output simultaneously, repair the sensors and inspect the steering angle sensor.
    3. If DTC C1439 and/or C1445 is not output again, the DTC may have been stored due to a temporary loss of the steering angle zero calibration, such as when the power voltage drops.



B
GO TO COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)

D
USE SIMULATION METHOD TO CHECK (Click here)
A


2. PERFORM STEERING ANGLE SENSOR ZERO POINT CALIBRATION
  1. Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds.

  1. Check that the centered position of the steering wheel is correctly set while driving straight ahead.

    HINT:
    If the front wheel alignment and steering position are adjusted as a result of an abnormal centered position of the steering wheel, acquire the yaw rate and deceleration sensor zero point again after the adjustments are completed.

    OK:
    The centered position of the steering wheel is correctly set.



NG
ADJUST FRONT WHEEL ALIGNMENT OR STEERING POSITION
OK


3. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more and turn the steering wheel to the right and left.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTCs C1439 and C1445 are not output
    A
    Yaw rate and deceleration sensor and/or steering angle sensor DTC is output
    B

    HINT:
    If DTC C1439 and/or C1445 is not output again, the DTC may have been stored due to a temporary loss of the steering angle zero calibration, such as when the power voltage drops.



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A

END


← C1439 Steering Angle Sensor Initialization Incomplete (+ C1445) (Aug 2011 – Jul 2012)C1439/66 Steering Angle Sensor Initialization Incomplete (+ C1445/66) (Aug 2008 – Jul 2009) →