2011-2016 FJ Cruiser · Service Manual BRAKE

DTC CHECK / CLEAR

Troubleshooting · Vehicles built from Aug 2012

Versions by build date: Jul 2007 – Jul 2008 Aug 2008 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012


DTC CHECK / CLEAR (when Using Intelligent Tester)
  1. Check for DTCs.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Chassis / ABS/VSC/ TRC / Trouble Codes.

    5. Read the DTCs by following the prompts on the tester screen.

  2. Clear the DTCs.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Chassis / ABS/VSC/ TRC / Trouble Codes.

    5. Operate the tester to clear the codes.

      HINT:
      Refer to the tester operator's manual for further details.


DTC CHECK / CLEAR (when Using SST Check Wire)

  1. Check for DTCs.

    1. Turn the ignition switch off.

    2. C263395E12
      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      SST
      09843-18040  
      Text in Illustration 
      *a
      Front view of DLC3

    3. Turn the ignition switch to ON.

    4. Read the DTCs output from the ABS warning light and slip indicator light in the combination meter.

      HINT:
      1. When the system is operating correctly, each light will blink continuously in a pattern of 0.25 seconds on, then 0.25 seconds off.
      2. When one DTC is output, each light will output the same code at 4 second intervals. (For example, Code 21 would be output as 2 flashes, a 1.5 second pause, and then 1 flash)
      3. When 2 or more DTCs are output, each light will output a different code at 2.5 second intervals, and when all codes have been output, there will be a 4 second pause and the sequence will repeat.
      4. When multiple codes are set, they are output in order starting with the lowest DTC number.
      5. If no code is output, inspect the TC and CG terminal circuit and the ABS warning light and slip indicator light circuits.

      Trouble Area
      See page
      TC and CG terminal circuit
      Click here
      ABS warning light circuit (Remains on)
      Click here
      ABS warning light circuit (Does not come on)
      Click here
      Slip indicator light circuit (Remains on)
      Click here
      Slip indicator light circuit (Does not come on)
      Click here

    5. The codes are explained in the code table.

      ABS DTC 
      ABS Warning Light Display
      Tester Display
      11
      C146E
      12
      C146F
      21
      C1468
      22
      C1469
      23
      C146A
      24
      C146B
      25
      C1225
      26
      C1226
      31
      C1401
      C1405
      C1409
      32
      C1402
      C1406
      C1410
      33
      C1403
      C1407
      C1411
      34
      C1404
      C1408
      C1412
      35
      C1413
      36
      C1414
      37
      C1337
      38
      C1415
      39
      C1416
      41
      C1241
      C1417
      42
      C1242
      43
      C1243
      44
      C1419
      C1420
      C1442
      45
      C1245
      46
      C1421
      C1422
      C1423
      C1424
      49
      C1425
      51
      C1251
      52
      C1252
      53
      C1253
      54
      C1254
      56
      C1256
      C1452
      57
      C1257
      58
      C1453
      C1454
      68
      C1268
      94
      U0073
      95
      C1240
      U0124
      97
      C1381
      VSC DTC 
      Slip Indicator Light Display
      Tester Display
      13
      C120A
      31
      C1432
      C1433
      C1434
      32
      C1232
      34
      C1435
      C1436
      C1443
      36
      C1210
      39
      C1336
      43*
      -
      53
      C1203
      62
      U0123
      63
      U0126
      64
      C1380
      65
      C1437
      U0100
      66
      C1290
      C1439
      C1445
      98
      C1440
      1. *: This DTC is output when the VSC system detects a malfunction in the ABS.

    6. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
      If 2 or more DTCs are output at the same time, the DTCs are output in ascending order.

  2. Clear the DTCs.

    1. Turn the ignition switch off.

    2. C263395E12
      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      SST
      09843-18040  
      Text in Illustration 
      *a
      Front view of DLC3

    3. Turn the ignition switch to ON.

    4. Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.

    5. Check that the ABS warning light and slip indicator light blink at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).

    6. Remove SST from the terminals of the DLC3.


END OF DTC CHECK/CLEAR
  1. Turn the ignition switch to ON.

  2. Check that the ABS warning light and slip indicator light go off within approximately 3 seconds.

← DTC CHECK / CLEAR (Nov 2010 – Jul 2012)FREEZE FRAME DATA (Jul 2007 – Oct 2010) →