2011-2016 FJ Cruiser · Service Manual CRUISE CONTROL SYSTEM

DATA LIST / ACTIVE TEST

System information · Vehicles built from Nov 2010

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Powertrain / Cruise Control / Data List.

  5. According to the display on the intelligent tester, read the Data List.

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    CCS Vehicle Spd
    Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Actual vehicle speed displayed
    -
    CCS Mem Vehicle Spd
    Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Vehicle speed stored in memory
    -
    Throttle Opening Angle
    Required throttle opening angle / Min.: 0°, Max.: 124.5°
    Required throttle opening angle
    -
    Cruise Control
    Cruise control / OFF or ON
    OFF: Cruise control not set
    ON: Cruise control set
    -
    Main SW M-CPU
    Cruise control switch (Main CPU) / OFF or ON
    OFF: Cruise control switch off
    ON: Cruise control switch on
    3
    CCS Ready M-CPU
    Cruise control system standby condition (Main CPU) / OFF or ON
    OFF: Cruise control switch off
    ON: Cruise control switch on
    1
    CCS Indicator M-CPU
    Cruise main indicator light (Main CPU) / OFF or ON
    OFF: Cruise main indicator light off
    ON: Cruise main indicator light on
    2
    Cancel Switch
    CANCEL switch signal / OFF or ON
    OFF: CANCEL switch off
    ON: CANCEL switch on
    -
    SET/COAST Switch
    -SET switch signal / OFF or ON
    OFF: -SET switch off
    ON: -SET switch on
    -
    RES/ACC Switch
    +RES switch signal / OFF or ON
    OFF: +RES switch off
    ON: +RES switch on
    -
    Stp Light SW M-CPU
    Stop light switch signal (Main CPU) / OFF or ON
    OFF: Brake pedal released
    ON: Brake pedal depressed
    -
    Cruise Operation Status*1
    Park/neutral position switch signal (D or 4 position) / OFF or ON
    OFF: Shift lever not in D or 4
    ON: Shift lever in D or 4
    -
    Cruise Operation Status*2
    Clutch switch signal / ON or OFF
    ON: Clutch pedal depressed
    OFF: Clutch pedal released
    -
    Brake Cancel Switch
    Brake cancel signal / OFF or ON
    OFF: Brake pedal released
    ON: Brake pedal depressed
    -
    1. *1: for Automatic Transmission
    2. *2: for Manual Transmission

    HINT:
    1. 3 is OK but 1 is NG → ECM failure
    2. 1 is OK but 2 is NG → DTC output or ECM failure
    3. 3 is OK but the cruise main indicator light does not illuminate → Cruise main indicator light, wire harness, or ECM failure


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Combination Meter / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. Lamp Cruise
    Cruise main indicator light
    ON/OFF
    Confirm that the vehicle is stopped with the engine idling.

← DATA LIST / ACTIVE TEST (Aug 2009 – Oct 2010)DIAGNOSTIC TROUBLE CODE CHART (Jul 2007 – Jul 2009) →